Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 59 minute(s) ago.

  1. Replies
    3
    Views
    45

    I was reading your statement as saying you were...

    I was reading your statement as saying you were cutting it out.

    Does the pattern dimensions match the actual scanned item size or does it show to the 1/8" smaller. If smaller you can set the size...
  2. Replies
    3
    Views
    45

    Did you "flip" the cut path in the cut path...

    Did you "flip" the cut path in the cut path settings?
  3. Replies
    2
    Views
    94

    Try increasing the "rendering cache" size up to...

    Try increasing the "rendering cache" size up to at least 256mb. It is found in the preference settings. If you are running the pro version turn off the "file preview" feature. It is under the help...
  4. Ken, I am sorry to hear you have not found...

    Ken,

    I am sorry to hear you have not found anyone for your carving requests.
  5. Not at all!

    Not at all!
  6. Thread: Angle help

    by fwharris
    Replies
    5
    Views
    106

    It looks a lot better, glad you were able to work...

    It looks a lot better, glad you were able to work through this.
  7. To change the pattern carving bit you need to go...

    To change the pattern carving bit you need to go into the board settings. The pattern bit is the bit used for ALL of the raster/pattern elements on the board.
  8. Thread: Angle help

    by fwharris
    Replies
    5
    Views
    106

    I played with this a little bit the other day. I...

    I played with this a little bit the other day. I "think" part of the problem is the restraints that you have pre set. Maybe try doing the angles first with the lengths close to what you want and then...
  9. Replies
    2
    Views
    522

    If you are a member of the Carvaholics on...

    If you are a member of the Carvaholics on FaceBook you might want to also post this there. If you are not I can post a link to this for others to see. Just let me know.
  10. Replies
    3
    Views
    76

    The picture is a bit fuzzy for me to see it...

    The picture is a bit fuzzy for me to see it good.. The most common place that the cable will break is right at the black support bracket and most times it is hard to see with out magnification or...
  11. Replies
    3
    Views
    76

    Look at the ffc ribbon cable, it could be...

    Look at the ffc ribbon cable, it could be torn/cracked. This was similar to the Z stalls I was getting and got the recommendation to get the a907 upgrade.
  12. Replies
    6
    Views
    196

    It should be a lot longer than that, but! Call...

    It should be a lot longer than that, but! Call CarveWright.
  13. Replies
    17
    Views
    537

    Great catch and only reinforces the need to watch...

    Great catch and only reinforces the need to watch and pay attention to what is happening during the start up routine.
  14. Replies
    15
    Views
    279

    Yes way to much done to let it go. As Dale and I...

    Yes way to much done to let it go. As Dale and I have instructed. Modify your design by drawing a rectangle over the area that has been carved. Leave the rectangle just short of where it stopped....
  15. I did the "try" feature but was only able to open...

    I did the "try" feature but was only able to open the pdf file. Have you tried to upload it to the card? If that does not work you should contact CarveWright.
  16. Do you have a link to the project? I've seen that...

    Do you have a link to the project? I've seen that warning before on a few projects that I have posted for others but they reported no issues when trying to use it.
  17. Replies
    15
    Views
    279

    No, the bit is bigger and will take more on each...

    No, the bit is bigger and will take more on each pass meaning less passes. Maybe should have said shorter.
  18. Replies
    15
    Views
    279

    Good choice if there no to little detail. Also,...

    Good choice if there no to little detail. Also, your carve time will be a lot faster
  19. Replies
    3
    Views
    117

    Glad to hear the cache size tip helped. Yes, not...

    Glad to hear the cache size tip helped. Yes, not all dxf files need to have closed vectors. It all depends on the design. Pay close attention when you select the close vector tool. I have missed...
  20. Replies
    15
    Views
    279

    Either! It all depends on how much detail there...

    Either! It all depends on how much detail there is in the design. If a lot of detail and you use the 3/16th the detail will not be carved as well.
  21. Replies
    15
    Views
    279

    As Dale said, draw a rectangle to cover the...

    As Dale said, draw a rectangle to cover the majority (95%) of what has been carved. Make the rectangle a carve region and then set the depth to zero 0 . Reload to the card and start it on the...
  22. Replies
    4
    Views
    208

    I deleted your other 2 posts on this subject....

    I deleted your other 2 posts on this subject. Please refrain from asking the same question multiple times.

    When setting your paths do one circle at a time. Zoom in real close to view what the...
  23. You have a stuck compression roller. Do as Dale...

    You have a stuck compression roller. Do as Dale said, do a compression roller sensor check.
  24. Replies
    17
    Views
    537

    They look great and glad you two are getting...

    They look great and glad you two are getting along now. There are several people who do use the CarveWright to make guitars and violins. Have seen the one in the CarveWright adds/intro on their web...
  25. Replies
    21
    Views
    509

    Like most everything else, make it smaller and...

    Like most everything else, make it smaller and bump the price up.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4