Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 34 minute(s) ago.

  1. Thread: Bulldogs "G"

    by fwharris
    Replies
    1
    Views
    27

    Try this..

    Try this..
  2. Replies
    20
    Views
    3,301

    Great bump Al! I had a good time chatting about...

    Great bump Al! I had a good time chatting about Chris's work and designs.
  3. Replies
    574
    Views
    81,888

    Sticky: I am not sure what the J material is either, this...

    I am not sure what the J material is either, this is just info I copied from someone who order them. Important part is the aluminum oxide open coat and the sizes.
  4. Replies
    574
    Views
    81,888

    Sticky: Brad, This a a great source for the sandpaper...

    Brad,

    This a a great source for the sandpaper belts http://customsandingbelts.com

    Ask for specify "j" material, Aluminum Oxide Open Coat W-15" x L-13" Grit-120 Dry

    Have/are you viewing...
  5. Replies
    2
    Views
    110

    In the search box type in "small font" including...

    In the search box type in "small font" including the quote marks. Discussion clear back to 2008.
  6. Replies
    7
    Views
    292

    The scanning probe will scan the complete piece....

    The scanning probe will scan the complete piece. Once scanned you can use the outline of the piece for cut outs.
  7. Thread: STL Files

    by fwharris
    Replies
    4
    Views
    293

    To use/make stl files into CarveWright patterns...

    To use/make stl files into CarveWright patterns you can use either the STL importer or Sculptor. The link will allow you to view how they operate.

    http://www.carvewright.com/add-on-modules/
  8. Thread: lost licenses

    by fwharris
    Replies
    6
    Views
    372

    Did you loose everything on your hard drive? Did...

    Did you loose everything on your hard drive? Did you have anything backed up?
  9. Replies
    4
    Views
    291

    Yes I would upgrade to the CarveTight Chuck.

    Yes I would upgrade to the CarveTight Chuck.
  10. Replies
    4
    Views
    291

    What chuck does it have? I am guessing it is a...

    What chuck does it have? I am guessing it is a sand paper belt that needs replaced? CW does not sell them any more but there is another source for them..

    ask for material, Aluminum Oxide Open...
  11. Replies
    5
    Views
    260

    [QUOTE=Tractorman;272850]There are a few fonts...

    [QUOTE=Tractorman;272850]There are a few fonts that have different symbols - Webdings and Wingdings - how do you pick ďoneĒ?[/QUOTE
    You use the font just like any other font.
  12. Replies
    7
    Views
    415

    You should not post your software license info...

    You should not post your software license info and machine ID
  13. Replies
    3
    Views
    139

    Do a "save as" to see where the last project was...

    Do a "save as" to see where the last project was saved to.
  14. Thread: Tree Pattern

    by fwharris
    Replies
    12
    Views
    607

    Typically an image is hard to make it into a good...

    Typically an image is hard to make it into a good pattern. To many high and low areas to get evened out.
  15. Replies
    1
    Views
    156

    Yes I have used a drawing tablet with designer.

    Yes I have used a drawing tablet with designer.
  16. Replies
    1
    Views
    177

    The files are to be opened with Designer.

    The files are to be opened with Designer.
  17. You will probably get a better answer if you call...

    You will probably get a better answer if you call them.
  18. Replies
    4
    Views
    259

    The install bit position is when the truck is in...

    The install bit position is when the truck is in the center of the machine. Trying to move it to another location when it is asking for the bit to be installed could/might cause a stall error.
    ...
  19. Replies
    15
    Views
    1,014

    Things that should help, Increase your...

    Things that should help,

    Increase your rendering cache size in the preference settings.

    Disable file preview under the help tab.

    Try to minimize the number of pattern you keep in your...
  20. Replies
    15
    Views
    1,014

    Also increase the rendering cache size.

    Also increase the rendering cache size.
  21. Look in the shared pattern section. There is a...

    Look in the shared pattern section. There is a zip file for all of the states outlines.
  22. Replies
    7
    Views
    315

    Michael Tyler posted the info some time back. It...

    Michael Tyler posted the info some time back. It included the step over rate for each upload quality setting I think.

    Results for searching "step over"
    ...
  23. That is do to the size and profile of the bit. I...

    That is do to the size and profile of the bit. I do all of my edge routing on the router table, not the CW.
  24. Replies
    3
    Views
    204

    I believe it is for the size you set up for the...

    I believe it is for the size you set up for the project.
  25. Thread: Sanding

    by fwharris
    Replies
    3
    Views
    156

    Sanding mops, radial sanding disc, diamond burr...

    Sanding mops, radial sanding disc, diamond burr tool for the drimile, sanding sticks.
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4