Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    1
    Views
    33

    What is the issue with 2.xx? Do you have 3.xx to...

    What is the issue with 2.xx? Do you have 3.xx to see if they work with that version and how about Basic?
  2. Replies
    1
    Views
    37

    I would verify the thickness of the pipe, it is...

    I would verify the thickness of the pipe, it is thinner than regular litho material. According to the instructions the pattern depth should be Set the depth to .170 and height to 999 and set Bit...
  3. Replies
    3
    Views
    203

    I would check the head pressure.

    I would check the head pressure.
  4. Replies
    5
    Views
    2,156

    https://forum.carvewright.com/showthread.php?22785...

    https://forum.carvewright.com/showthread.php?22785-Table-top-finish&p=202258#post202258
  5. Replies
    3
    Views
    203

    You probably had a display message about scaling....

    You probably had a display message about scaling. It asked if you wanted to scale the project or load a new board. If you said yes to scaling it reduced the project size. Scaling is caused by the...
  6. Thread: ER20 spindle

    by fwharris
    Replies
    13
    Views
    546

    Check with CarveWright to see if they still sell...

    Check with CarveWright to see if they still sell this. It says discontinued but shows up in the store. It fits the square hole on top of the spindle.. OR you can grind down something to fit.
    ...
  7. Replies
    46
    Views
    5,852

    It should not be to long before you are out...

    It should not be to long before you are out cruising the neighborhood. Getting any requests yet?
  8. Replies
    7
    Views
    391

    Glad to hear you made the switch, thanks! With...

    Glad to hear you made the switch, thanks! With corian make sure you are using a good sharp clean bit. Even though you are using my attachment there will still be chips that get into the machine...
  9. Replies
    5
    Views
    353

    Greg, To attach a file to a post use the "Go...

    Greg,

    To attach a file to a post use the "Go Advanced" icon and the bottom right of a normal post. Once there scroll down to "manage attachments" to upload a file.
  10. Replies
    4
    Views
    852

    This is a great place to get started......

    This is a great place to get started... http://support.carvewright.com/
  11. Replies
    4
    Views
    852

    Welcome to the forum! Sorry to hear about your...

    Welcome to the forum! Sorry to hear about your Dad. Since you are just getting started you should begin with visiting the CW web site and their SUPPORT section. There you will find the Learning...
  12. I would first take out the Y motor and gear box...

    I would first take out the Y motor and gear box to verify that the bearings are bad and if the shaft shows any wear signs. You can order replacement bearings at this link or from other places like...
  13. Thread: Depth of cut

    by fwharris
    Replies
    5
    Views
    814

    You are welcome! Hey we both got it right!

    You are welcome! Hey we both got it right!
  14. Thread: Depth of cut

    by fwharris
    Replies
    5
    Views
    814

    Something like this? Each rectangle set at a...

    Something like this? Each rectangle set at a different depth.
  15. It might be loosing the Y position or feeling...

    It might be loosing the Y position or feeling some resistance. Make sure the Y rail and bearings are clean and lubed. http://support.carvewright.com/cleaning-the-y-and-z-rails/

    Check the Y gear...
  16. Replies
    5
    Views
    497

    Great job from both of you. I have a lot of the...

    Great job from both of you. I have a lot of the coin patterns but not the capped bust dollar.
  17. Replies
    5
    Views
    449

    Great! Looking forward to seeing some of your...

    Great! Looking forward to seeing some of your work with it.
  18. Replies
    8
    Views
    2,768

    That is a bad link. the forum is not running any...

    That is a bad link. the forum is not running any more... this is the page http://allcw.com/


    I found this by doing a search for "ai2mpc" using the quote marks. Several pages of discussion. I...
  19. Replies
    5
    Views
    449

    Take a look here maybe.. I am not sure if any of...

    Take a look here maybe.. I am not sure if any of these guys are still around or not...

    https://forum.carvewright.com/showthread.php?7070-Simple-vector-paths-in-AutoCAD-How-TO&p=52397#post52397
  20. It should work for the crank.

    It should work for the crank.
  21. On the main page of the forum scroll down to the...

    On the main page of the forum scroll down to the "on line tools" and there is a section to care and maintenance schedule. It will take you here....
    ...
  22. Thread: Bit question

    by fwharris
    Replies
    2
    Views
    727

    I would think you could, just know that the carve...

    I would think you could, just know that the carve area will be larger than the design size. I would suggest to carve in multi passes and not very deep per pass.
  23. Replies
    247
    Views
    68,033

    Sticky: Happy Easter to you Oscar.

    Happy Easter to you Oscar.
  24. Replies
    5
    Views
    947

    Cool car! Thanks for the share.

    Cool car! Thanks for the share.
  25. Replies
    4
    Views
    320

    If you have the pattern editor or sculptor you...

    If you have the pattern editor or sculptor you can edit the pattern you created when you imported the stl into Designer. Open up the pattern tool to show the patterns in your favorite list. Next,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4