Search:

Type: Posts; User: Mugsowner; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    488

    The sensor saw light color then dark color and...

    The sensor saw light color then dark color and thinks it has crossed the board, giving a bad width measurement. The work around I use is masking tape in a T pattern placed where the sensor travels to...
  2. [QUOTE=Mike1;274049]This happened to me as well...

    [QUOTE=Mike1;274049]This happened to me as well but in my case the wood was too dark (pre-stained). I used a piece of natural wood as a test, and it worked fine.[/QUOTE
    When I use wood to dark for...
  3. Replies
    4
    Views
    194

    Are you using an offset or inset? The bit cuts...

    Are you using an offset or inset? The bit cuts the middle of the path. Depending on the bit size, the 1/8" bit would need a .062 inset on the inner and a ,062 offset on the outer. How well does the...
  4. Replies
    592
    Views
    89,179

    Sticky: Welcome, I would have to agree with Floyd on...

    Welcome, I would have to agree with Floyd on this. The tracking roller travels the bottom side of the board, on the keypad side of the machine. Make sure your board does not have any issues on the...
  5. Replies
    2
    Views
    249

    The quick change chuck was replaced with the...

    The quick change chuck was replaced with the Carvetite chuck system. If you need the quick change adapters, they are out there. I have a few I could part with, as I have Carvetite in all my machines.
  6. Replies
    328
    Views
    31,054

    Looks sharp Oscar

    Looks sharp Oscar
  7. Replies
    2
    Views
    227

    What would be shipping to 54130 for the 8x10's?

    What would be shipping to 54130 for the 8x10's?
  8. Replies
    10
    Views
    441

    Cutting is a sharp flat nose, and carving is a...

    Cutting is a sharp flat nose, and carving is a curved/angled point, right?? Right
    Did I have a wrong bit in the machine at some point and it remembers that measurement? No
    And wants to see...
  9. Replies
    6
    Views
    314

    The switch on the left side is for the cover,...

    The switch on the left side is for the cover, the switch on the right is for the motor.
  10. Replies
    3
    Views
    164

    Try going to your carve list and clicking on it...

    Try going to your carve list and clicking on it there. I have seen this before and that is ow I get around it.
  11. Replies
    3
    Views
    342

    Happy New Year

    I would like to wish all of you and your fiends and families a Happy New Year. Hope it is a good one.
  12. Replies
    592
    Views
    89,179

    Sticky: Welcome Dave, sorry to hear you are having card...

    Welcome Dave, sorry to hear you are having card issues. A while back cards were chatted about and one of the ideas that came up was to put a piece of tape on the cards to make them easier to remove...
  13. Replies
    8
    Views
    526

    As for the picture you could run through some...

    As for the picture you could run through some photo software to clean up. When you use a vector, you will have to select a bit, in this step you will be asked to select depth of cut.
  14. Replies
    3
    Views
    203

    I to would like to wish all of you and yours a...

    I to would like to wish all of you and yours a very Merry Christmas!
  15. Replies
    6
    Views
    405

    I would agree with Al the epoxy repair would be...

    I would agree with Al the epoxy repair would be much stronger.
  16. Replies
    6
    Views
    405

    Nice job on the repair. The tywraps may give you...

    Nice job on the repair. The tywraps may give you an issue, but I do not think they will not. The strength you added to the cable housing holding power is huge. Not sure if repair would hold without...
  17. Thread: Trinket box

    by Mugsowner
    Replies
    17
    Views
    854

    Hello Oscar, the design is great. I think a...

    Hello Oscar, the design is great. I think a trinket box with a delicate nature should have a shallow carving applied to accent the box. Deeper carving seem to aggressive to me for delicate projects....
  18. Today I think is my last day with internet. There...

    Today I think is my last day with internet. There is no internet where I spending the next two weeks or so.
  19. I have a motor that brunt out on me. I could...

    I have a motor that brunt out on me. I could remove the casing. The problem I have is I will not be near the motor for a couple weeks. I will be back the first week in December.
  20. Replies
    4
    Views
    279

    I have an old motor here that I can view the...

    I have an old motor here that I can view the cable end. What I see is just a square opening on the end, but I think there is a ridge where the square stops. The square looks to be a threaded insert,...
  21. Replies
    4
    Views
    279

    This could be the same issue. The cable may that...

    This could be the same issue. The cable may that a broken wire which is rubbing the sheath and causing the run up to be hampered a bit, causing the message. I would check the brushes to make sure...
  22. Replies
    10
    Views
    548

    When you load the carving bit, place a shim on...

    When you load the carving bit, place a shim on the keyboard edge of the board. The board does not move while finding bit and surface. After the machine goes thru the bit finding you can hit the stop...
  23. Replies
    63
    Views
    2,865

    Yes the clutch is behind the handle. There are...

    Yes the clutch is behind the handle. There are shims behind the handle. They are between the handle and spring and are used to push the spring forward putting pressure on the crank torque plate. The...
  24. Replies
    63
    Views
    2,865

    Low head pressure could be caused by the clutch...

    Low head pressure could be caused by the clutch releasing early, in which case you would have to shim to increase pressure.
  25. Replies
    4
    Views
    718

    These machines can be purchased with issues...

    These machines can be purchased with issues fairly cheap. All of mine were purchased used.One first was carving all over the place, looked closer, I found a cracked Z truck frame. Ordered a new Z...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4