Search:

Type: Posts; User: bamaman315; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. Need help converting this picture into a good carving pattern

    87065can someone help me convert this into a good carving pattern? I have had no luck. Thanks in advance.
  2. Thread: cut motor

    by bamaman315
    Replies
    3
    Views
    433

    replaced the x termination board , the capictor...

    replaced the x termination board , the capictor blew out the card
  3. Replies
    1
    Views
    147

    Truck cant make up its mind

    Trying to do a carve and while setting up the bits the truck moves to the bit plate and checks the bit , but when it starts to come to the key board side it keeps jerking back and forth. Any ideas?
  4. Replies
    3
    Views
    578

    do you have a picture of this ?

    do you have a picture of this ?
  5. Replies
    7
    Views
    566

    under the machine , I thought the termination...

    under the machine , I thought the termination board was behind the rail to the right on keyboard side of machine.
  6. Thread: cut motor

    by bamaman315
    Replies
    3
    Views
    433

    cut motor

    I have 2 machines and both have same issue with cut motor . I tried replacing the termination board and still same thing . any ideas?
  7. Replies
    5
    Views
    674

    update , I went back to shop I moved the Z truck...

    update , I went back to shop I moved the Z truck to center of machine and ran test again and it passed , but when I tried to test cut motor it said motor was running but it was not , any ideas?
  8. Replies
    5
    Views
    674

    Z Axis Stall Error code E06-0324

    I have issues with this code , I have replaced the 14 pin cable , and replaced the y motor because of the encoder wheel broke loose from shaft , I also replaced the termination board. I ran the test...
  9. Replies
    16
    Views
    730

    Ok I must have a elf that went into garage and...

    Ok I must have a elf that went into garage and worked on my machine, I came in today and loaded a regular carving pattern on a different card and machine went through the steps with no problem. so I...
  10. Replies
    16
    Views
    730

    same error message different machine , when using...

    same error message different machine , when using the rotary jig with long bit , the truck goes to the right side and the bit touches the bit plate one time , then I get the error message. Any ideas?
  11. Replies
    16
    Views
    730

    ok just came in from shop got rid of the error...

    ok just came in from shop got rid of the error code. problem now is when I do the tests , everything works good until it gets to testing the cut motor. The display says motor running hit any key to...
  12. Replies
    16
    Views
    730

    Ok went back to the shop this morning and...

    Ok went back to the shop this morning and replaced the termination board again and did the manual tests and all test worked but just as soon as it went to the z axis test it throws up error message...
  13. Replies
    16
    Views
    730

    I already replaced the termination board . are...

    I already replaced the termination board . are they two of them ? The one I replaced is where the Y motor plugs into
  14. Replies
    16
    Views
    730

    I wish it was that simple , I even rotated the...

    I wish it was that simple , I even rotated the cap for the cable 180 out and still same issue
  15. Replies
    16
    Views
    730

    I have the long bit that came with the rotary...

    I have the long bit that came with the rotary jig. I have already done multiple carvings and all came out good . I'm not missing any steps when trying to carve. The bit used to rotate after you...
  16. Replies
    16
    Views
    730

    https://youtu.be/nKkpw3a9C3g here is the video...

    https://youtu.be/nKkpw3a9C3g
    here is the video link finally got it loaded , I think ?
  17. Replies
    16
    Views
    730

    Error Code E05-324

    I am starting to have some major issues with my machine . I am working with the rotary jig with 3 inch pvc pipe as show in the carvewright site. I load the project the machine homes itself then it...
  18. Replies
    1
    Views
    373

    rotary lamp ( mona lisa )

    There was a step by step with pictures of how to make this project , I wrote down all the parts I needed but now I cant find the instructions . can anyone tell me where it is located please?
    Thanks...
  19. I tried the pattern and when I changed it to...

    I tried the pattern and when I changed it to centerline the names went away , it also says I need a license to use the conform option . What program do I need for that?
  20. how can I get the names on this pattern to carve in centerline

    85977 trying to figure out how to load carve the names without chunks being knocked out
  21. Replies
    1
    Views
    376

    I need help with pattern

    85839I need help converting this to a good carving pattern , can anyone help me out?
    Thanks in Advance. 4.25 tall by 9.25
  22. Replies
    17
    Views
    1,442

    After reading the replies , I went out in the...

    After reading the replies , I went out in the shop and took a good look at my machine . Guess what I saw? The exit tray was tilted down , I adjusted the tray and everything has been running smooth. I...
  23. Replies
    17
    Views
    1,442

    I have had no issues before , I have already made...

    I have had no issues before , I have already made 4 other using the same pattern. My board is actually longer that what the pattern calls for. I did use masking tape under the board with same results
  24. Replies
    17
    Views
    1,442

    84470 This is what it is doing this is the...

    84470
    This is what it is doing this is the second attempt
  25. Replies
    17
    Views
    1,442

    getting ticked off about tracking issue

    As we all know wood is not cheap , I have been trying to carve the coin bank pattern and when it comes to the cutting out process it ends up cutting into the pattern. what am I doing wrong? Please...
Results 1 to 25 of 264
Page 1 of 11 1 2 3 4