Search:

Thank You gentlemen. I finally determined I was being bitten by requesting to stay under The rollers. This was adding the additional dimension. The Text is actually back far enough so that was not...

I am working on a project where I want to orient a letter in each of 6 boards. I laid out the letters and snapped distance from the end of the eah figure. When the letter carves it is not in the...

I have sent you a private message. Dan

I have been ill for a protaracted period of time. Tonight when I attempted to bring up designer to update it and my probe I received a message stating that my trial period was over. My machine was...

This morning I did a thorough look thru my machine to look for obvious problems. Did not find any and restartd the scan. Lo and behold it failed in the same area. Closer examination reveale a...

Dan, what problem caused you to have the Z truck replaced? I am experiencing a Z AXIS stall error 246. I was using the probe when it happened. Prior to that happened I noticed that the menu was...

Ken the phone message says the operating times are Mon thru Friday and instructs to leave a message. Thank you. Will wait till monday.

Dan

I received the Z AXIS stall error 246 after 10hours on my Beta Replacement machine. I received this while scanning a project with the probe, therefore I do not think there was any undue pressure.
...

I have a design of a switch panel for a boat. The design consists of a group of raised 'buttons' using the vertical dome surface. In the MPC theyt look as I would like them, however when they are...

I think you are correct sir. It was asking for the bit to be loaded and I hit enter which made the machine think I had loaded the requested bit. Going to try again and see what happens. Thanks for...

This is the first time I used my 'BETA REPLACEMENT' machine. The first project carved until a bit replacement was called for. The display showed 'load the 90 deg bit' , I hit enter expecting the...

My machine was ordered well prior to the cut off date of mid July. I was going to be out of town and keeping with thier excellent support LHR held shipping it until I returned home. First...

I just received my 'trade in' for my Beta Machine. It arrived with a Craftsman logo plainly visible. I contacted LHR and was assured that the new Craftsman and CarveWright machines are vertually...

I just received a call from CarveWright and the offer to upgrade the Beta machines will expire on July 15, 2007. This saved me from missing out as I am going away and will be gone until July 14th. ...

When this happened to me I had to send the CW to Huston. These wheels are pressure fitted and should not come off.

That is one ugly cat.

Very nice work. I bought the Jantz video and am trying to work with it in Xara. Great signs Good luck.

I actually talked to the Bard around 2 central time. He had just returned from lunch. I guess someone felt a little nourshment was necessary.

Bard defines the word customer service. Lets all...

Congratulations Sarge, You will be spending more time now. Like Pkunk I have sold some stuff but most of it stays in the house or with friends.

Glad to have you aboard.

The 'bushing' I am referring to is the small brass thing on the end of the shaft that goes into the Ztruck.

After some maintenance, when I was putting the shaft back I realized I had not captured the little bushing. Pretty good chance my goat ate it cause I can not find it.

Will someone tell me what...

This emblem was created using the probe. The original was 1 1/2 inches high.
I carve this at least .740 depth to get the best detail. A carve region is also recommended.

Dan

Here is an Emblem that was created using the probe. It carves nice with little cleanup. The detail is better when the depth is .750 or more. The original came from a large brass placque and is 1...

I found a screw laying on my project, and followed the instructions for removing the cover and found where it went. It was the right hand screw on the Z motor mount. I returned the screw without...

Thanks Rick, I guess I worked too long last night.

Dan