Anyone have a Teenage Mutant Ninja Turtle design???
thankyou
Type: Posts; User: mannwranglers; Keyword(s):
Anyone have a Teenage Mutant Ninja Turtle design???
thankyou
Carvewright machine and Dust Vac needs to go.....
$1200.00 firm....no less
Location
Florence,SC
29501
843-992-6526
Has anybody carved a Head Board for a bad......
If so......what width and length???
Redneck Tech
George,
Florence,SC
Can anyone tell me if it matters about the sand paper belts or those rubber belts?
I've read that you have to calibrate the machine if you get the rubber belts....is this true??
I got a new...
Is there a way to route an already carved design??
my machine did an excellent carving....but faulted out when it went to check the 90 degree router bit on the keypad side.
Is there a way that I...
Mr. AL & Mr. JOE....
these 2 generous people helped me to solve the problem of why the bit was burning the wood instead of cutting and carving it.
Mr Joe was kind enough to sell me a cutting...
I'd like to send out a couple of BIG THANK YOUs to Mr.AL and also to Mr. JOE who have been so very helpful to me in the lasts 2 months!!
Both of them have helped me by email and also by phone....
Hello,
does anyone know where I may be able to find the ALLAN HEAD FLAT SCREWS that go in the roller bearings of the Z Truck????
Please let me know
If anybody knows how to get this machine from off the Accessory Menu......
Please let me know...... I put the cutting motor back in and now it is stuck on the Accessory Menu and I need to get it...
69962I hope this will play.....I took a 38 second video of what its doing.....maybe you guys can tell me what is going on!!!!!
George
I cannot believe this.....
Took out the old Z Truck Assembly and put in another.
I fought for 3 hours getting the roller bearings tight!!!!
And tried to do a cross cut to test it.....& it's still...
Tying to find a solution to the problem that I have with my machine.
It's smoking when it cross cuts and chewing up the board when it carves.
Mr. AL told me that i have a loose bearing.
Any...
69752I'm looking for the person that designed this........I'd like to try and get the designs of the screw driver, wrench, cogs and bolts!!
This will be a very big project for me and a lady is...
Just had a strange request for a carving for a High Heel Shoe.
If anyone hasa design like that .....please let me know!!
Thanks,
George
SC
Hello,
I'm searching for Carvers in or near my location.
I live in Florence SC.
Maybe we can share ideas and tech support about this machine!!
Thanks,
George
Hello,
I'm searching for Carvers in or near my location.
I live in Florence SC.
Maybe we can share ideas and tech support about this machine!!
Thanks,
George
Hello,
I got a cool request today for a design for DADs Day that this person wants a Hammer, Pliers and a wrench design to be made for their dad for upcoming fathers day gift.
if anyone has...
Looking for a Wooden Nickel design with the Indian Head!!!!
Any help will be greatly appreciated!!!!
Thanks,
George,SC
If anyone has an extra cut motor housing,especially the bottom half....I'd like to try and buy it!!!
Thanks,
George
69499
69478
This happened today to my carvewright machine....
The bottom part, where the flex shaft goes in to the cutting motor fell apart or came off.....I don't know what happened to it.
I was in...
I got asked about a Chevy Bel Air design.....like on the 1957 Chevrolet.
It's the V shape with Bel Air.....does anyone have any designs like this.......It's for a person that is going to put his car...
has anyone tried drilling a hole at about .650 and about 12 inches round.....
I tried to do it and it came out oblong.....any pointers??
George,
SC
While doing a carving.....I heard a clicking noise and then my machine stops and on the keyboard it reads " Clean Y Rails".
Previously...... I took the back cover off the Y Motor and cleaned...
wondering if anyone has the HARLEY-DAVIDSON logo without the "HARLEY-DAVIDSON" lettering in the middle.....
please let me know!!!
George,
SC
Any body had their machine to stop when it went to cross cut a board??
It's been about 5 months since I did any carving or cutting with it.
Guess I got to do some greasing and fighting to it before...