Search:

So Zan where do I find Sculptor? And how do I use it? For future reference. Im still on the first version.

Perfect! Thank you so much for taking the time to work on this! It really means a lot to me. You are a truly wonderful person :D

Thanks Zan! I was kinda hoping for more of 3Dish look to his face. His nose, cheeks and hair still are being carved low and not high.

Can someone help with this picture? A friend of mine father inlaw passed away a short time ago and I'm trying to make a carving out of this picture of him. This is the only one I could get my hands...

Here's a picture of one of many odd shaped pieces of material I have to carve. I was going to post last night but got a little sleepy on the couch LOL

77495

Thanks everyone for all the great ideas! I really apologize for my absence to my post. I've been really busy trying to put my wood shop back together. Pulled everything out and installed a new floor...

I'm looking for ideas on how to build a sled for oval pieces like rough cut lumber that might still have the bark on. Pieces that are not straight and square and are still holding the unique look of...

Replaced the FFC cable and problem solved! Back to carving! Thanks again!:)

I think I'm going to do the A907 upgrade and see if that resolves the problem

Z axis stall err E06-0313 and edge detection failed err E03-0400

I've replaced the board sensor and still getting these error messages. When checking the sensor while moving the truck assembly...

Hello everyone!

Looking for a pattern of the state of Wisconsin that I can also use the cut path to carve and cut out for some deer antler mounts.

Thanks for any help!

Tim

What is the best way to get the old bearings out of the gearbox? Can you tap one down until it in turn pushes the first one out then continue until the second one drops?

Thanks!
Tim

Thanks everyone for your replies!

This is one idea that I'm toying around with. When I get time I will use someof the other ideas and see what else I can come up with.
I'm recently doing some...

Thank You!
That gives me a GREAT start!

I'm also considering trying to paint some areas of the project to make them "pop" a little more.
Does anyone have any points or ideas on the type of...

Hello everyone
This past July 30th a very close friend (and like a 3rd son) of the family past away and I would like to create a plaque for his dad which is also a close friend I've known since...

Hello all
I've recently noticed that the flexshaft on my carvewright seems loose on the truck. Even when fully snapped into place when I grab it with my hand I can move it back and forth. I also...

That looks pretty good! Thanks! This is the one I was playing around with....

Hello
I'm Looking for a Pattern of a Northern Pike. Just a straight shot Picture would be pefect. Nothing jumping out of the water or something. I've tried using something off of the internet but...

I also replace my power supply following LHR's troublshooting of my carvewright shutting down for no reason. I purchased the upgrade PS and soon after was getting the black bars on the screen like...

$40.00 for the power supply and $100.00 for the contoller.

*Update*
Well after receiving and installing the new controller I did an hour long test carve that completed successfully. Now I'm wondering if it wasn't the controller right from the beginning....

Morning All
Just received shipping confirmation via email stating the controller and memory card will be here sometime on Wednesday. I will post after installation to let you guys know if the...

Thanks Ike for the input. Actually I had started out with replacing the power supply. On test one it would go through the project, keep under roller, cut to size, measure then select bit all fine....

Hi all
Alex. I believe it was possibly you I spoke with on the phone today about my issues. Told you I had to think about it. I decided to go ahead with the parts I called and asked the question...

Well just off the phone with LHR and he is thinking its either the memory card or the controller. $300.00 for the controller and $55.00 for the card. Lovely.....