https://www.ebay.com/itm/225127411568?hash=item346aa3af70%3Ag%3AA0cAAOSwuPdjAQi2&amdata=enc%3AAQAHAAAAoDs%2F1NLZ9%2F1Bwz8Pha1pLH1aeuCxEtlaOKoJCCVyw3%2FdeIqAE4KqwhQBc4ePiowPSX5W9mBw9rhMYXK3AQwFui%2F5Mi...
Type: Posts; User: DickB; Keyword(s):
https://www.ebay.com/itm/225127411568?hash=item346aa3af70%3Ag%3AA0cAAOSwuPdjAQi2&amdata=enc%3AAQAHAAAAoDs%2F1NLZ9%2F1Bwz8Pha1pLH1aeuCxEtlaOKoJCCVyw3%2FdeIqAE4KqwhQBc4ePiowPSX5W9mBw9rhMYXK3AQwFui%2F5Mi...
Are you using a longer board and staying under the rollers?
You need to check the compression roller switches as I described. It's simple and easy to do. The board sensor is not used until the roller drops. If the switch is dirty or stuck, the machine will...
Select Options (0) - Sensor Check (7) press Down Arrow to display roller status. Crank down on your board. Front and Back Rollers should both read Compressed.
I have not found an exact replacement in stock - most are much smaller in length. I have a few suggestions.
Samtec offers a 20-pin cable in the length that you need. I would try trimming one with...
What I am asking is the cable a "Type A" or "Type B" per the attached photo.
88660
We also need to know the pitch of the contacts. If the cable is 3/4" wide, with 18 contacts the pitch should...
Are the contacts on the same side of the cable, or opposite sides?
A cable may be available through electronics suppliers. Please measure the exact length and width of the cable, and if possible the spacing between conductors (will likely be in metric). Also a...
FYI. I have not used one myself.
88659
Stimulus check? ;)
It can reduce carve time, and yes the X and Y work together with Centerline.
The attached examples are on a 12" x 6" board. Centerline time is 3:34 and Raster 6:31.
88650 88651
If...
I would suggest Centerline and Conforming Vectors for signs as suggested by lynnfrwd. I would hold off on purchasing Pro until you find that you need it, unless budget is not an issue. That said,...
After pressing 7 (Measure), press 1 to select Length (nothing will happen until you select Length or Width). If the board moves, the controller is probably OK and it is either a bad display or a bad...
If the controller were bad I would think the machine would not even go through the homing process. I would pretend everything was OK and try an operation such as Measure to see if it works. I can...
It seems to be an issue with Designer Pro. It works for me in Designer Basic, but not Pro - I get the same result as you no matter the font.
As a workaround, you could break the date into 5...
I don't have a "bullet" on my keyboard. How are you entering it?
Yes, please elaborate on what you would like to do in your projects.
You can use raster and the Invert tool. Best with no feather and shallow depth.
Use the Flip to other side of the model tool, it will change from pink to brown and you can proceed.
Can you post the image that you imported?
Run a board sensor test: http://support.carvewright.com/checking-and-cleaning-the-boardsensor/
Post results.
This is the best technique to easily "carve" a photo in wood. I use quotation marks because you're not really converting a photo to 3D, but creating slightly higher (lighter) and deeper (lower)...
ER11. Many collet sizes available. I have one similar to this for my CarveTight spindle: ...
I would not go that deep - .125" would be plenty.
Please post the original image (or a link) and your mpc.