Search:

Type: Posts; User: dante4488; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,296

    Tool Icons not saving

    I've spent an hour rearranging my icons on Desiner pro 3. I've made sure I have no new updates. I have also made sure that the reset tool box after closing the program is off as well. Every time I...
  2. Replies
    1
    Views
    4,358

    Drawing tablet

    Good afternoon everyone, just wanted to see if anyone out there uses a drawing tablet instead of a mouse in the software. I do a lot of tracing/editing and was looking for opinions. I’m not done...
  3. Replies
    8
    Views
    14,569

    Al, Thank you very much for all the information....

    Al, Thank you very much for all the information. I’ll look into all these things that could be the problem(s). I truly feel like you’re trying to help because I would NEVER type that much,lol. I’ll...
  4. Replies
    8
    Views
    14,569

    There is no hole next to the roller. When is...

    There is no hole next to the roller.
    When is tries to bob next to the board,right before it’s about to start.


    Sent from my iPhone using Tapatalk
  5. Replies
    8
    Views
    14,569

    Everything checks out with what you both were...

    Everything checks out with what you both were saying. I did just notice though it’s certain projects that are giving me errors. Does that make sense? I haven’t upload these projects on my card again...
  6. Replies
    8
    Views
    14,569

    New Z motor now E06-0324

    I installed a new z-motor with no problem. Afterwards I did 4 or 5 new cutouts in a sled, like I’ve always done with no problems. Now all of a sudden it measures the board, it asks the general...
  7. Replies
    0
    Views
    632

    Software Picture Great to Bad

    I’ve done a number of photos that have turned out just fine. The problem is that when I change the bit optimization to high or best for a split second while it’s optimizing the photo looks the best...
  8. Replies
    1
    Views
    12,421

    2 Sided thickness

    My carving depth is set at .468 on each side. My height on each side is 100%. The Walnut that I’m using is 1.25 thick. I need my final thickness of the carving to come out to .937. I keep getting a...
  9. Replies
    1
    Views
    879

    Machine went blank

    My machine stopped working in the middle of running a project. I wasn’t by the machine when it stopped, so I calmly walked up to it thinking it was the “check cut motor” but the LCD screen was...
  10. Thread: Larger Bit?

    by dante4488
    Replies
    8
    Views
    2,109

    Thank you for the information. The thickness of...

    Thank you for the information. The thickness of material is 98% of the time 7/8 thick. I do three - four passes normally because of the shaking I get from the flex shaft. I am just extremely...
  11. Thread: Larger Bit?

    by dante4488
    Replies
    8
    Views
    2,109

    I'm cutting 7/8" thick stock. When I try to do it...

    I'm cutting 7/8" thick stock. When I try to do it in one pass the flex shaft shakes so badly, even with a new bit. Is it just normal for the flex shaft to shake like that when cutting in one pass? I...
  12. Thread: Larger Bit?

    by dante4488
    Replies
    8
    Views
    2,109

    Larger Bit?

    I primarily use my machine for cutouts. It works great but I would like to be able to do it a little faster. The bit I use is the 3/16" cutting bit. I have to do multiple passes in the same area to...
  13. Replies
    12
    Views
    2,873

    Thank you very much sir. Will try it as soon as I...

    Thank you very much sir. Will try it as soon as I get home.
  14. Replies
    12
    Views
    2,873

    I will check these parts, but I sure hope not the...

    I will check these parts, but I sure hope not the machine has less than 25hours on it.
  15. Replies
    12
    Views
    2,873

    I'm using a 3/16" cutting bit. Thank you all your...

    I'm using a 3/16" cutting bit. Thank you all your help
  16. Replies
    12
    Views
    2,873

    No Sir/Ma'am But please tell me, Even if I did...

    No Sir/Ma'am
    But please tell me, Even if I did would it have lines like the pic above?
    I've used the Bit and cutout a few times with no issues.
    Thank you ALL for any info.
  17. Replies
    12
    Views
    2,873

    I'm using the 3/16 Cutting Bit.

    I'm using the 3/16 Cutting Bit.
  18. Replies
    12
    Views
    2,873

    3/16" Cutting bit

    3/16" Cutting bit
  19. Replies
    12
    Views
    2,873

    Cutout problem

    I'm doing cutouts, I have the bit run around 3 or more times so I don't try to cut out 13/16" thick lumber all at once. The problem is each cut is a little larger from the last. Meaning if the cut...
Results 1 to 19 of 19