Search:

Type: Posts; User: sjwilson57; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    18
    Views
    35,251

    Requested Features for next version

    I would like to see a tape measure or ruler function for measuring, like Google Sketchup.
  2. Replies
    644
    Views
    330,064

    Sticky: What if your board width is a standard size,...

    What if your board width is a standard size, let's say 11.25" and I want to have my dado (pocket) cut through the side. According to the video, you can't do this because of the rollers. That means I...
  3. Replies
    7
    Views
    1,767

    Steve N., I'll try it again using a higher...

    Steve N.,

    I'll try it again using a higher resolution image. I'll post the results when completed.
    Thanks for the advice.

    Steve W.
  4. Replies
    7
    Views
    1,767

    I edited my post and re-added the photo. ...

    I edited my post and re-added the photo.

    Thanks,

    Steve
  5. Replies
    7
    Views
    1,767

    Lousy Carving Quality

    I can never get a good quality carve from my Carvewright. I hope someone can tell me what is going on. I have attached the .mpc and a picture of the end result.


    Any help would be appreciated....
  6. Replies
    17
    Views
    4,803

    Thanks Dick, I'll either get or make a new...

    Thanks Dick,

    I'll either get or make a new pattern for the circled one.

    Next time I'll try your method for two sided projects.

    You're north of Brainerd, about an hour and a half from me.
    ...
  7. Replies
    17
    Views
    4,803

    RogerB, I don't know of any Carvers in my...

    RogerB,

    I don't know of any Carvers in my area. I live in the St. Cloud Minnesota area. One of the main problems I have is; I travel every week, and only have weekends to work with the...
  8. Replies
    17
    Views
    4,803

    Thanks Henry1, I'm trying to remain positive. I...

    Thanks Henry1, I'm trying to remain positive. I have carved some items with success, but have never been satisfied with the quality.

    I've owned the Carvewright for several years now and wish I...
  9. Replies
    17
    Views
    4,803

    Project files

    7510575104
  10. Replies
    17
    Views
    4,803

    Yes, I made a jig and used masking tape. I did...

    Yes, I made a jig and used masking tape. I did end up removing the tape from the sides of the jig. It still carved lousy. I hope my third time carving this design after some changes that I made to...
  11. Replies
    17
    Views
    4,803

    rickroy, I bought it new.

    rickroy,

    I bought it new.
  12. Replies
    17
    Views
    4,803

    Lousy Carving Quality

    I have not had any real success in having a clean carve since I bought this CNC. I'm beginning to regret the purchase.

    The first picture has no real quality in the carving, what am I doing...
  13. Thread: -Objects

    by sjwilson57
    Replies
    337
    Views
    236,107

    Sticky: Lawrence, So, if I post a picture of a hammer,...

    Lawrence,

    So, if I post a picture of a hammer, I must be a carpenter? Only a Liberal would think that way. I'm offended by your presumption.
    I'm a Conservative and I honor the Constitution, which...
  14. Replies
    27
    Views
    13,585

    I make mine in the shape of the State where I...

    I make mine in the shape of the State where I live (Minnesota). I have also used the State shape for a clock as well. I then sell them in my store.
    72782
  15. Replies
    13
    Views
    4,347

    Why not cut the pattern and then scan it back...

    Why not cut the pattern and then scan it back into Designer, then create another editable pattern. I have never tried this, but it sounds like it would work.
  16. Replies
    3
    Views
    1,266

    Good to know. Thanks!

    Good to know. Thanks!
  17. Replies
    7
    Views
    3,718

    Thanks Bigtyme for the feedback. I'm not familiar...

    Thanks Bigtyme for the feedback. I'm not familiar with the Sculptor software, is that what is needed for the Rotary Jig? I just have to chuckle (cause crying is out of the question) that every...
  18. Replies
    3
    Views
    1,266

    Vertical Guide Rods/Plastic shroud cracks

    I just noticed cracks in the plastic shrouds that hold the vertical guide rods. There's a crack on every corner (see pic).


    72753

    Has anyone else experienced this issue? If so, how can I get...
  19. Replies
    7
    Views
    3,718

    Designer 3.0

    I'm considering purchasing Designer 3.0 upgrade. I have Designer 2.0 already. If anyone has purchased and downloaded Designer 3.0, I would like to know if it is worth the $200 upgrade price? Does it...
  20. How to I get rid of an arc in my pattern and vertex additions are frustrating

    I placed an arc in some line segments and now I can get rid of it!!! How do I delete an arc that is not wanted. The arc was not placed between the two vertex' where I didn't want it; it seems to...
  21. Replies
    1
    Views
    1,021

    Cut Path and Pattern saving

    I hope someone here can help me with this one. I created a scroll saw pattern of a Butterfly .
    66609
    When I save it as a pattern, this is what I end up with ,66611 but after setting it as pierced...
  22. Creating Scroll Saw Patterns using CorelDraw X5

    I have CorelDraw X5. It does a great job creating vector drawing from bitmaps with just a button click, but what I want to do is make the open areas that one would cutout on a scroll saw as the carve...
  23. Creating Scroll saw patterns using CorelDraw X5

    I have CorelDraw X5. It does a great job creating vector drawing from bitmaps with just a button click, but what I want to do is make the open areas that one would cutout on a scroll saw as the carve...
  24. Replies
    3
    Views
    1,299

    I have attached the image that I used for import....

    I have attached the image that I used for import.
    64887

    Thanks,

    Steve
  25. Replies
    3
    Views
    1,299

    Improper Technique or bad pattern

    I cut this Angel from a clip-art that I edited using Pattern Editor.

    Why when it cuts, it looks choppy and fuzzy (Poor detail). What can I do to make it clearer? Do I need to sharpen my bits? ...
Results 1 to 25 of 42
Page 1 of 2 1 2