another way to do the drill holes if your going to drill them by hand is use the text tool set with 5 periods in a row and but them on you layout use a 60 degree bit that's w hat I do when I find a ...
Type: Posts; User: hrlevill; Keyword(s):
another way to do the drill holes if your going to drill them by hand is use the text tool set with 5 periods in a row and but them on you layout use a 60 degree bit that's w hat I do when I find a ...
Would love to get the mpc for the best hand in cribbage w would gladly pay for it you can send it to me are hrlevill@gmailcom
There's Been a lot of discussion on the web at different times about cribbage boards design etc. I have made many many of them.as gifts over the years by hand and with the CW and the design I...
Just want to.THANK DAN for getting me all squared away with the UBC!!!! It sure will.save a lot of WOOD
Correction my last post the machine asked for Y after the X and then I.put in 25. Sorry about that it is working crazy to.say the least!!!
Dan here is where I am today with my. Carrier and it crazy tried different things jog to touch point line jig the x kept telling me to o
Load 1/8 which was already in the Chuck did that a few times...
Ok when you are carving a cribbage board I use 3 bits first load is the 90 degree I crank the head down all.the way next is the1/8 cutting bit it dose it's thing and that's when I hit stop jog 3 hit...
Here's where I am with what is going on with my carrier one time it cuts the depth say with a 60 degree bit fine the next time it CARVES to.deep Dan clear me up.on something that may be...
Thanks Dan will.give it another try when it states load the 1/8 bit I do that dose it's thing I hit stop and jog3 it states to jog it to the front touch point carrier directions I do.that and I...
Join the club I have that problem when doing 5/4 boards for cribbage boards with the carrier the bit CARVES to.DEEP and I follow the carrier directions to the letter carve the same board on the...
Wish he could but he is at a loss to figure what is going on on my end I sent him my
MPC for a board and he said it worked fine for him. !!! On his machine I even redid my MPC thinking something...
Mike the thing is not the holes as I could not check them as I stop.the machine as SOON as I saw it was carving why to.deep.in the letters and numbers on the board I do not pick the depth of cut on...
Mike just checked it out the carrier is 3 1/2 in. High with a 5/4 board in it and the rails lowered down so the5/4 board sticks up 1/8 above the side as per instructions the total hight is 3 5/8 high
Don.t know will have to.check it
I have been in touch with Dan many times and he can not under stand it either and here is what is happening if i try to.carve a cribbage board that is 5/4 wood with .the carrier and follow all the...
I made one of the carriers found one think in the instruction that Don.t jive it's state put the short touch pad on one side and the long one on the other thing is my touch pads were cut out both...
I have taken PTN that BJB has done for me.many times transferd them.to.my favorites file and made changes in them and worked fine for me
I have the1/32 bit and dose a super job I use it on all my carves now much better detail !!!
i have done many boards and i cut the pocket hole in the bottom of the board to hold the pegs with a 3/4 in stright bit about 2 to 3in long cut or what ever i then make a cut on each side of it...
haveing made a lot of cribbage boards by hand and with my cw i note that a lot of you that are designing boards are forgeting one big thing you have start point which is fine BUT you forget to inc. a...
to those of you makeing or designing cribbage boards the holes should be 1/8 by 0.50 anything smaller than that forget it as most pegs made are 1/8 and if the hole is only 0.25 its not deep enought...
would you be willing to share your mpc for your board if so why not post it
thanks will give it a try should have bad weahter next few days so will not be rideing and will work in thw shop seeya
will not be working in my shop till the snow flies but i think it will work will send you a donation (please, do not post personal information)
looking for an mpc of the Harley Owners Group logo anyone have it or could set it up for me i can be reached through a Private Message.