Search:

Type: Posts; User: Dirtydan; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    11,410

    There is only one size... I normally get my...

    There is only one size... I normally get my 60degree bits at Sears... The shank might be a little longer, but not much.
  2. Replies
    17
    Views
    4,856

    Ok, I broke the code.... The cutting bit with the...

    Ok, I broke the code.... The cutting bit with the pre-installed collar needs the 1/2" stop collar installed also. Did't have that problem when I was using the split collar and my old cutting bit. ...
  3. Replies
    17
    Views
    4,856

    While that sound like a fix for something I might...

    While that sound like a fix for something I might have done ("put the guide on backwards") but I haven't done anything to the machine except update the software and change over to the new bit...
  4. Replies
    960
    Views
    367,384

    Ken, Boy that really came out Very Nice... ...

    Ken,

    Boy that really came out Very Nice...

    Guess I'm going to start coming back to this forum more often... Been awhile...

    Again, REAL NICE and Clean...:)
  5. Replies
    19
    Views
    11,410

    Yes, I got the adapter... I was just wondering...

    Yes, I got the adapter... I was just wondering if I also had to use the spacer with it or not....
  6. Replies
    19
    Views
    11,410

    [ USING BITS & PROBE WITH CARVETIGHT: •New...

    [
    USING BITS & PROBE WITH CARVETIGHT:

    •New Scanning Probes will feature hard pressed steel collars
    •Existing Scanning Probes can be updated with a slotted steel collet

    Good luck,...
  7. Replies
    3,314
    Views
    3,118,211

    Sticky: No, but if you find one let me know....

    No, but if you find one let me know....
  8. Replies
    960
    Views
    367,384

    Great Idea Ken....:-D

    Great Idea Ken....:-D
  9. Replies
    960
    Views
    367,384

    Hope this helps.... 1. Enter the text you...

    Hope this helps....

    1. Enter the text you want on the board. Raster Mode only.
    1a. Set Depth to 0.100
    1b. Set Height to 999 (This sets the top surface of the letters at the top of the...
  10. Replies
    960
    Views
    367,384

    Klinger, Now I understand what you were...

    Klinger,

    Now I understand what you were asking... I did it just like I said... I stained the board with the Ebony stain.

    CarveWright does not like dark wood... but here's what you do... The...
  11. Replies
    2
    Views
    1,277

    Thanks Doc.... I thought that was true, but...

    Thanks Doc.... I thought that was true, but thought I'd ask before I broke something else... I was wondering why they even left the Circuit Card on the Truck... It looks like the wires to to an...
  12. Replies
    2
    Views
    1,277

    Oops I Broke It

    Z-Truck.... On the Z-sensor Circuit Card there is two wired that go to a black recepticle on the left side of the truck as you look at it.. Mr. fat fingers broke the recepticle and a little more......
  13. Replies
    960
    Views
    367,384

    1 Your right, I ment Outline Pattern.... 2. I...

    1 Your right, I ment Outline Pattern....
    2. I normally don't use raise lettering as it requires extra carving time to remove the wood around the letters instead of just carving the letters. If I...
  14. Replies
    960
    Views
    367,384

    Stain...not paint...

    I don't like to put paint on fine wood, so what I do is use an Ebony Stain on the entire board after carving. While it is drying, I flood the area's I want to appear black. It will take about two...
  15. Replies
    8
    Views
    2,208

    Ouch....#$%* Computer's

    Well it looks like it is the computer... $$$ Shipping isn't cheap either:p I should be back up Friday... Key word being "Should"... I'm guessing it over heated... That whole area was packed with saw...
  16. Replies
    8
    Views
    2,208

    Unitedcases... From one Gunny to another...

    Unitedcases...

    From one Gunny to another thanks for your input... Tomorrow is break-down day and troubleshooting... Hoping for the best, expecting the worst..
  17. Replies
    8
    Views
    2,208

    Thanks Al... I'll check it first thing in the...

    Thanks Al... I'll check it first thing in the morning... I've been cutting the pieces out and sanding all night... Project was due out tomorrow, so I've been busting butt... We'll take the...
  18. Replies
    8
    Views
    2,208

    Well the card appears to be OK... I tried...

    Well the card appears to be OK... I tried pluging it in again, with the same results... Is there a connection on a board I can check???
  19. Replies
    8
    Views
    2,208

    Machine Just Stops - No Error Message

    After 3+ hours of carving and just starting to cut-out the patterns the machine just stopped. Display "Carvewright Machine"... No error message, nothing... Pushed the stop key, noting, pushed the...
  20. Replies
    13
    Views
    6,886

    Thanks for the reply Joe.... I have a friend...

    Thanks for the reply Joe....

    I have a friend who sandblast various stone media, while it is a great 2D representation of a design, it's not 3D like you would get with the CW. Laser is another...
  21. Replies
    13
    Views
    6,886

    Want to get Stoned

    Has anyone ever carved on Granite or Marble? If the answer is YES…. What kind of projects did you make? How did the bits hold up? Idea’s!!!!!! :confused:
  22. Replies
    13
    Views
    6,886

    The material carves very nice, but the machine...

    The material carves very nice, but the machine clean-up is a pain. The carving leaves a sand like material that gets everywhere even with a good dust collection system. Be sure to remove the...
  23. Replies
    42
    Views
    13,966

    The mpc file was an example of how to do it... ...

    The mpc file was an example of how to do it... You can only do one side of the supports at a time.... To save time, I'd just delete the supports from the file and utilize the rest. Acutally, I'd...
  24. Replies
    42
    Views
    13,966

    Revise MPC

    Made it a little simpler... But remember you will have to cut to size and then do the 45 degree picture frame cuts your self...

    Correction, the board or Sled will have to be 47" long and at...
  25. Replies
    42
    Views
    13,966

    Light box MPC

    I just made a down and dirty one for you to play with. As I said before, these pieces are done much eaiser on a table router... I mainly use the CW for the Corian Carvings...

    To use the MPC...
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4