Search:

Type: Posts; User: wlkjr; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    15,169

    Thanks Al. I have an interested buyer but we...

    Thanks Al. I have an interested buyer but we haven't worked out all the details yet. I'll post when it's sold. I took up the shooting sports, reloading and bullet casting several years ago and my...
  2. Replies
    7
    Views
    15,169

    Carvewright FOR SALE

    I bought this machine around 10 years ago and did a few projects. Totally lost all interest. Nothing wrong with machine. Due to health issues, probably won't use machine again. It has not been used...
  3. Replies
    0
    Views
    907

    Selling CarveWright

    Bought this machine in July of 2012 but have used very little. Has 18 hr. 24 min. on cut motor. It has the rubber belts and a Ringneck Blues dust collector. Also included are several bits and a 1/4"...
  4. Replies
    2
    Views
    2,355

    I've got about 72 of the plastic Painter's Pals....

    I've got about 72 of the plastic Painter's Pals. I've also used scrap pieces with brad nails shot from the bottom and sticking up about 1.25"
  5. Replies
    162
    Views
    95,054

    I assume Ebay would be much cheaper since LHR's...

    I assume Ebay would be much cheaper since LHR's shipping is a little high.
  6. Replies
    6
    Views
    1,901

    I almost went but didn't want to go to the...

    I almost went but didn't want to go to the northside of town. I thought the admission price was a little steep and saw no discount coupons. Would have liked to have seen Capt. Bruce again and meet...
  7. Thread: memory card

    by wlkjr
    Replies
    3
    Views
    1,187

    More like you can pour the mix out the pan but...

    More like you can pour the mix out the pan but you can't put it back in.
  8. Replies
    12
    Views
    2,900

    Don't you just love it when you can't even use...

    Don't you just love it when you can't even use the machine you bought because someone else has control?
  9. Replies
    162
    Views
    95,054

    Gotcha. I see the need now, especially for the...

    Gotcha. I see the need now, especially for the shanks smaller than 1/4
  10. Replies
    162
    Views
    95,054

    What makes the ER11 better than a collet adapter?...

    What makes the ER11 better than a collet adapter? ...
  11. Thread: Table top finish

    by wlkjr
    Replies
    21
    Views
    7,389

    I dug this up...

    I dug this up http://www.youtube.com/watch?v=-5uSTYNURJ0
  12. Thread: Table top finish

    by wlkjr
    Replies
    21
    Views
    7,389

    There is a spray that will pop the bubbles. It...

    There is a spray that will pop the bubbles. It has been several years since I poured any epoxy and I can't remember what it was. Worked great for me. It came in a about an 8 oz. pump sprayer.
  13. Thread: software

    by wlkjr
    Replies
    3
    Views
    2,655

    My understanding is that the license can be...

    My understanding is that the license can be transferred but it must be deactivated from the original two. Someone correct me if I'm wrong.
  14. Thread: Panel Saw

    by wlkjr
    Replies
    17
    Views
    7,228

    I love my homemade panel cutter. Ripped a piece...

    I love my homemade panel cutter. Ripped a piece of 1/4" plywood about 12" wide and stapled a 1x2x1/2 thick down the middle. Then run your circular saw against the guide and rip off the edge. That...
  15. Replies
    20
    Views
    7,687

    How much do those weird size filters cost for it?

    How much do those weird size filters cost for it?
  16. Replies
    20
    Views
    7,687

    I use a homemade system built with a squirrel...

    I use a homemade system built with a squirrel cage motor out of an old furnace. It has a high and low speed and works well in my 20x40 shop. I can spray some black spray at one end of the shop and in...
  17. Replies
    14
    Views
    4,516

    My philosophy is "Do I want to be tired and broke...

    My philosophy is "Do I want to be tired and broke or rested and broke?" Unless it's for special friends I'd try to make a minimum of $20 per hour. At that you still wouldn't be making that much. I'd...
  18. Replies
    16
    Views
    5,357

    I'm all for that. All my knowledge could be put...

    I'm all for that. All my knowledge could be put on the point of a pin. Not even enough to cover the head.:(
  19. Thread: US-Georgia

    by wlkjr
    Replies
    37
    Views
    19,658

    I bought the Ringneck blues dust collector and...

    I bought the Ringneck blues dust collector and have been happy with it.
  20. Replies
    16
    Views
    5,357

    I'm from Thomaston and Capt. Bruce is from...

    I'm from Thomaston and Capt. Bruce is from somewhere around Snellville.
  21. Replies
    25
    Views
    7,346

    I'm only working piddly part time stuff and...

    I'm only working piddly part time stuff and sometimes I think that's too much. Time's wasting my friend. Make yourself a Mock headstone that says "Wish I had spent more time at work" and look at it...
  22. Replies
    25
    Views
    7,346

    I'm glad you're in driving distance. I can just...

    I'm glad you're in driving distance. I can just bring my projects up and contract the painting out to you. The painting is definitely the hardest part.
  23. Replies
    12
    Views
    3,791

    I love the looks of the clocks.

    I love the looks of the clocks.
  24. Thread: Underlining

    by wlkjr
    Replies
    9
    Views
    2,060

    Did a test cut and it worked. Just can't figure...

    Did a test cut and it worked. Just can't figure out how to move the line up and down in small increments. Seems to jump further than I want.
  25. Thread: Underlining

    by wlkjr
    Replies
    9
    Views
    2,060

    Thanks guys. Looks good on the software. Will try...

    Thanks guys. Looks good on the software. Will try it on a test piece.
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4