Search:

Good Idea!!! bcause I do have quite a library on the PC
Thank You!

I haven't had as much time with the Mac using this program as what I have the PC. But I could have sworn that some MPC files loaded into the PC when I installed the software. And the PC has a folder...

I now have a Mac and PC sitting next to each other. I generally use the Mac with a Wacom tablet instead of a mouse for all the graphic work I do. However when I bought the Compucarve all I had...

I received on a card a MPC file titled pretty circle from Carvewright. It is a circle approximately 7 inches in diameter and has a fancy floral design in the middle. It is beautifully detailed. When...

I have not carved this yet but the picture was in todays paper, so I've greyscaled it &etc. hopefull it will turn out okay.
Enjoy!

Yes ! I've had this happen several times. It will send report, the indicator bar shows 100% but it does not ever show completed. I end up clicking cancel to turn it off. I never know whether or not...

We have similiar problems with Limitorque valve actuators at the power plant with setscrews and a bulletin from the manufacturer recommends Loctite, spot drilling and staking the threads. This...

I know it would swing out but it would just pop out and then would not wait for the bit to come down and touch it. Hopefully y'all are correct in this dilemma that was making me wander just why I had...

Now its working. So what was the problem? I'm still confused. The swinging plate was not staying out long enough for the bit to come down and touch it. So I printed out the sticky PDF file and...

I'll have to try it tommorrow when I get home from work, but I don't know for sure as the plate is not going out to hit the bit until after the bit has gone up and out of the plates reach. It doesn't...

I did a carving tonight and afterwards it was to cut a ogee and then cut out the board but when it got to the ogee bit it just kept asking me to load bit. What in the world is going on here. Now all...

Facing the keypad, I jogged the wood to start carving at the right corner nearest the keypad. It jogged to what appeared to be approximately 3-1/2 to 4" from the end and stopped which appeared...

The machine measured it

I just measured. It scaled down to 10" by 6" and the 10" was lengthwise and the 6" was the width. I don't think that was the problem. The end measures 4-3/4" left from where it was carved out and the...

the board was about 4 ft long and 11.25 in. wide. the carving should have been approx 12" long and 8" wide. the board was large enough not to sacle the work. I did tell it to stay under rollers and I...

I have done a few carvings and when doing some of them the machine gives me a choice of carving to scale or loading a new board. I know that I have at least 1/2 inch clearance on each side and ample...

I'd like to know about the colored pencil trick. Tried searching for it, but did not see it anywhere.

I had at one time the complete jewelery box as one file and like a fool deleted it however I still have it on the card and a couple other patterns that where deleted off the computer and would love...

Anyone have any idea what the average turnaround time is for a machine when it is sent to Carvewrigt for repair? (Just curious)

Newport News

I have talked to the Bard this week and he is the one I wanted to talk to and I did get lucky. I was seriously considering taking my broken machine back to Sears; but, after talking to the Bard I...

Well, I am very glad to hear about the fantastic service.
I've had quite a few problems with the machine I bought from Sears and was considering taking it back for a refund as currently I am going...

Have Not called CW yet as they are hard to get hold of and I have sent a message to the Bard though.
It took over a month just to get bits.
The machine is still under warrenty with Sears. Plus I...

I just upgraded my software and formated and flashed my card and still am getting the Assert Macro Error 87.
Still dead!
HELP!!!

Now I just reflashe dthe card downloaded the same project and when I turn on the machine it immediatly gives me the ASSERT Macro failed.
It appears I'm dead in the water.