Thanks, that is what I thought I was doing but haven't had any luck I'll give it another shot as it's been a little while since I tried it. Sometimes I'm able to miss the most obvious solution:???:...
Type: Posts; User: Sconi; Keyword(s):
Thanks, that is what I thought I was doing but haven't had any luck I'll give it another shot as it's been a little while since I tried it. Sometimes I'm able to miss the most obvious solution:???:...
I have been looking in the users guide, and in the tips and tricks archive, and am wondering if there is a comprehensive explanation about jog to center, corner etc., been trying to make that work...
Thanks I'll see if I can do the math :D and give it a try.
Often when I enter a new number I get a out of calibration range error. When it will accept a number it only takes one so small it doesn't change the location significantly or at all.
Spent half a day trying to re calibrate the Y offset based on the on-line instructions from the CW website. Didn't have much luck, did a forum search and found that the on line instructions don't...
I broke my second 1/8 cutting bit today, I was cutting a purchased project, in 3/4 pine, it was on it's second cutting pass when it broke. I'm going to check the cover switch to make sure vibration...
That is a great clock, outstanding work sir!
Many thanks to the folks who share patterns on the forum, I'm pretty certain that is where I got the logo.
One of today's projects. It's gonna be a key holder and probably hang a couple of hats on it. Couldn't resist a tribute to my favorite toy. Once I figure out how many pegs I'll trim it to size. Not...
Thanks, that is what I needed to know!
Been using the original UCB for a while and now that I have a second machine I find myself in need of an additional one, I have been skimming through the posts on this topic and need a summary of...
Thanks I'll try that, the depth was incorrect on the original, I had changed it but apparently didn't save the change..... measure twice cut once again proves it's worth.
Working on a honey do project, and need to make some grooves 1/8 wide by 2 1/2 wide and 1/4 deep, using designer 3 I thought I made some but they cut 1/4 wide, I can work with the 1/4 wide, I think,...
Surprised that no one has offered any thoughts on this, I'm not familiar with that error code but you might try reformatting the card under the flash management option.
Very nice project.
Nice design, I really like those, well done sir!
Made several Christmas gifts this year, four of the Little Artists Crayon Caddy, two of the Classy Christmas Wreath, and one Christmas Candle Centerpiece all by CarveBuddy, and one domino train game...
Yes sir I did, it read 156 most of the time, but did read low once in a while, it was a fairly new sensor - a couple of months old but I replaced it just in case and nothing changed.
Thank you Al,
I do have spare roller bearings and screws on hand already, had a similar experience in the past.
The butt Floss Trick was done before and it didn't seem to make much...
Probably a duh question here but I'm going to replace the board sensor cable on one of my machines to see if that corrects an intermittent board sensor failure problem, and possibly the fcc cable as...
THANKS! I did glance at the calibrating instructions but I must have missed the depth option, I just had to adjust the board length so I'll give that a try. I appreciate the link.
I should have been more clear I was using the normal 1/16 and 1/8 bits that come with the collar on them. I do have some of the clear stop collars so I can use them. Giving it more thought the bit...
I'm kind of an intermediate level user but learning all the time, I keep getting a message wood may be too thin, but it's 3/4 and the mpc says 3/4, so there isn't a problem there. When changing bits...
I have a new unused QC cutting bit available, just pay the shipping!
After trying almost everything it was Lateral Stabilizer just got it installed today and gonna try to carve something tomorrow!