Search:

Type: Posts; User: Woodlegend; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    690

    Text over text

    I have used my carvewright machine for several years doing the basics.
    I am trying to go to the next level.
    I would like to use a monogram letter and put a name over it.
    What is the best method of...
  2. Replies
    4
    Views
    843

    Bit Confused

    I have sent my machine to get it upgraded. I confused with which bits will work. I looked at my bit set and the 1/2" has a nut, that i assume I remove to use the 1/2" straight bit. The 1/4"...
  3. Replies
    4
    Views
    748

    Thanks for everyones help. I found a slight tear...

    Thanks for everyones help. I found a slight tear in the keypad cable that probably is the cause of the frozen keypad. Will replace
  4. Replies
    2
    Views
    887

    My machine needs to be fixed and I could use...

    My machine needs to be fixed and I could use another machine. I would offer $800, that seems to be what used machines are selling for.
  5. Replies
    4
    Views
    748

    Freezes at Stay Under Roller Prompt

    I was told problem was with Memory card. I replaced memory card and when I begin project I am only able to get to the stay under roller prompt 1 or 2. When I hit the keypad for either 1 or 2...
  6. Replies
    7
    Views
    1,849

    Stay under rollers

    I finnally was able to solve the close cover switch, but now I only get to the message for option 1 stay under rollers. When i hit the keypay it will not do anything. Checked the keypad connector...
  7. Replies
    7
    Views
    1,849

    close cover

    Checked plug and white wire was to center of machine. Any other suggestions appreciated, Thanks.
  8. Replies
    7
    Views
    1,849

    Close Cover problem

    I checked sensor option 7 which said cover open.
    Is there any other suggestions?
    Thanks
  9. Replies
    7
    Views
    1,849

    Close cover error

    I had a error message 319. I checked the brass roller O-ring and it was fine. I cleaned and blew cout the two roller switches.
    I changed the board to see if that solved the problem. And i kept...
  10. Replies
    2
    Views
    769

    How to Find Hours of use on Machine

    How do you find out how many hours machine has been used?
  11. Replies
    3
    Views
    965

    Carving a picture (logo)

    Need help with eliminating carving backround when importing a picture.
    I import a picture of say a logo and invert the carving area. But the backround around the picture is also carved slightly....
  12. Replies
    1
    Views
    756

    License Pattern

    I have purchased a pattern and installed it in my carvewright favorites, but it won't allow me to use it. I have tried to license it but it does not appear in the license box. I tried to update and...
  13. Replies
    1
    Views
    618

    Pattern Editor

    How do I get pattern editor installed?
    I have purchased the complete package with scanning probe, but pattern editor does not show up in the licenses.
  14. Replies
    2
    Views
    846

    Close cover message

    I have installed the z-motor and now I cant' get past the close cover message, even if cover is closed. Do you have a solution?
  15. Replies
    8
    Views
    1,193

    246 Error

    Thanks I was able to get the plate to touch and then I got a 246 axis error.
    What is the cause of this error?
  16. Replies
    8
    Views
    1,193

    Bit Plate

    Is it the plate on the opposite side of the of the sensor? Where to you stick the tape on the plate side that touches the bit?
  17. Replies
    8
    Views
    1,193

    Stuck in loop asked to load bit

    I have not been able to get past the load bit command. I load the bit and the machine goes to homing and goes back to laod bit. I have reloaded the project and rebooted and have the same problem....
Results 1 to 17 of 17