Search:

Type: Posts; User: Mugsowner; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Today I think is my last day with internet. There...

    Today I think is my last day with internet. There is no internet where I spending the next two weeks or so.
  2. I have a motor that brunt out on me. I could...

    I have a motor that brunt out on me. I could remove the casing. The problem I have is I will not be near the motor for a couple weeks. I will be back the first week in December.
  3. Replies
    4
    Views
    184

    I have an old motor here that I can view the...

    I have an old motor here that I can view the cable end. What I see is just a square opening on the end, but I think there is a ridge where the square stops. The square looks to be a threaded insert,...
  4. Replies
    4
    Views
    184

    This could be the same issue. The cable may that...

    This could be the same issue. The cable may that a broken wire which is rubbing the sheath and causing the run up to be hampered a bit, causing the message. I would check the brushes to make sure...
  5. Replies
    10
    Views
    354

    When you load the carving bit, place a shim on...

    When you load the carving bit, place a shim on the keyboard edge of the board. The board does not move while finding bit and surface. After the machine goes thru the bit finding you can hit the stop...
  6. Replies
    60
    Views
    1,694

    Yes the clutch is behind the handle. There are...

    Yes the clutch is behind the handle. There are shims behind the handle. They are between the handle and spring and are used to push the spring forward putting pressure on the crank torque plate. The...
  7. Replies
    60
    Views
    1,694

    Low head pressure could be caused by the clutch...

    Low head pressure could be caused by the clutch releasing early, in which case you would have to shim to increase pressure.
  8. Replies
    4
    Views
    509

    These machines can be purchased with issues...

    These machines can be purchased with issues fairly cheap. All of mine were purchased used.One first was carving all over the place, looked closer, I found a cracked Z truck frame. Ordered a new Z...
  9. Replies
    12
    Views
    668

    I do the same as Jerry to a point. My jig is...

    I do the same as Jerry to a point. My jig is mounted to one of my routers. It is a piece of poly carbonate with an edge guide mounted to it. The edge guide is mounted 3/4" off bit center. Any other...
  10. Replies
    12
    Views
    668

    Yes the keyhole function is an add on that needs...

    Yes the keyhole function is an add on that needs to be purchased. The cost is around 50 dollars and comes with a bit, I believe. A new bit would run you about 30 dollars, so with the bit it is a...
  11. Replies
    5
    Views
    488

    Get bit of info. Enjoy the fact that I can view...

    Get bit of info. Enjoy the fact that I can view the inside of the programmer without tearing it apart. I always dread the first opening of any item I have never worked with or seen worked on.
  12. Replies
    3
    Views
    261

    Tablerock I sent you a private message

    Tablerock I sent you a private message
  13. Replies
    6
    Views
    489

    I do not have any issues at all. This is just of...

    I do not have any issues at all. This is just of bit of info I picked up here, where others have mentioned issues that may have been caused by the lighting. Not saying you will have problems, but...
  14. Replies
    6
    Views
    489

    Led lighting is great and easy to work with....

    Led lighting is great and easy to work with. Being low voltage the issues of shock go away. The intense light from led tends to mess with the measuring process, so it would need to be shut down for...
  15. I thought I would try to make a tabletop model. I...

    I thought I would try to make a tabletop model. I think the dowel that is needed is 1 inch dia. about 4 inches long not adding for recessed amount.
  16. There is a table top design out there as well....

    There is a table top design out there as well. Same design, but just a disc with a full circle cove.
  17. Great job Oscar, not to beat up on the design, as...

    Great job Oscar, not to beat up on the design, as it does seem to have most of what is needed and I can not open the mpc to view, so I am going off the pictures uploaded. The recessed ring should be...
  18. Replies
    16
    Views
    15,653

    See If this works for you.87708

    See If this works for you.87708
  19. Replies
    11
    Views
    852

    Wow, this really shows the skills and imagination...

    Wow, this really shows the skills and imagination you have. Your project looks great and shows the workmanship that had to be exercised. Great job
  20. Replies
    18
    Views
    1,646

    I did some looking around to see if I could find...

    I did some looking around to see if I could find a answer for you. This is what I found. Extruded has higher tolerances and if thickness checked should be with in .05, where cast can be as far off as...
  21. Replies
    198
    Views
    18,133

    Nice work Oscar

    Nice work Oscar
  22. Replies
    1
    Views
    355

    Evening glad to see people do still lurk out...

    Evening glad to see people do still lurk out there. not sure if this will help or not, but here it goes. When you want to move a single line there should be a hand type cursor for selecting. When...
  23. Replies
    4
    Views
    948

    Happy memorial day

    Just wanted to stop in and wish everyone a happy Memorial day and weekend. Stay safe and enjoy.
  24. Replies
    580
    Views
    86,726

    Sticky: Welcome Jeffery, Hope the machine preforms well...

    Welcome Jeffery, Hope the machine preforms well for you. The Carvetite spindle is an upgrade, however the sand paper belts are not. They work, but do tend to slip now and then. There is a few points...
  25. Replies
    2
    Views
    338

    Put the tape in a T shape. One across where the...

    Put the tape in a T shape. One across where the sensor measures width then again where the sensor looks for the the edge of board.
Results 1 to 25 of 486
Page 1 of 20 1 2 3 4