anatomy of the carve tight spindle

Can someone explain the anatomy of the interior of carve tight spindle?

On my latest carve, my 1/8" cutting bit broke at the conclusion of the carve. That may have no bearing on my question. but when I tried to insert another bit, there seemed to be significant resistance. I continuously loosened the tightening screw and finally removed it. When I feel inside the collet with the tip of my pinkie, there seems to be something flat inside. Is that part of the tightening mechanism? Have I dislodged something? The tightening screw doesn't seem to want to tighten completely, and I certainly don't want to strip the threads. I've tried to look at the opening with a mirror, but I can't get a good view.

I've had difficulty recently with bits sticking in the collect, and have often had to crank down on bits using the split collet adaptors in order for them to stay in place.

Any suggestions?

There is a little barrel type thing with one end curved lie the inside of the spindle and it is threaded thru it's center. I find the if you wiggle the inserted allen T wrench, it will wiggle the barrel and the bit will come out.
Clint

OK, but I can't get a bit in, and the screw won't go in completely. Perhaps that pice is out of alignment?

You should be able to push the inside part out of the chuck with a small wire/pick. It might have a small burr on it.

And to address the broken bit at the end of the carve, I would be looking at your Y Gear box Bearings.

I agree... a "Burr" inside the crimp nut.

AL

Clint,
The bit is out. That is not the problem. Chris at CW tech support says the piece is backwards and I have to pull it back out of the screw hole! I have no idea how to do that! I can stick my finger into the collet from the bottom and feel the piece, but I can't get any leverage on it. I can't get the tightening screw to catch, so that is not a solution. I've tried wiggling the hex wrench through the screw hole as well as an ice pick and a small screwdriver. All to no avail! any other suggestions? I hope you can understand this image.
Attachment 81069

t-town
We just induced the same problem in one of our machines in an attempt to figure out what is going on. It appears that the part of the collet/spindle with the threads that the set screw engages is free floating (which makes sense) and has shifted. I was able to get ours in a similar position by removing the setscrew and sticking the allen wrench in the hole and gently wiggling it around. To put it back in its normal position I used a screwdriver tip from an eight way screwdriver and pushed it back into place from the inside of the spindle. We made a short video, if anyone would like to see it PM us. After the piece is straight you will want to put a bit with collet up in place and hold it there while starting the setscrew in its threads (this will hold the floating piece in place).
Butch & Dian

Well, if I had software to convert the 38meg, 17 sec .mov file, I could share it! :(

Here are some pictures to help. This shows how it should look on the inside and how the paw is shaped with a curve to accommodate bits. You have the noncurved part of the paw in where the bit goes instead of lined up with the screw hole.
http://uploads.tapatalk-cdn.com/2016...948960d8de.jpg
http://uploads.tapatalk-cdn.com/2016...6877598f64.jpg
http://uploads.tapatalk-cdn.com/2016...05c20a220a.jpg
http://uploads.tapatalk-cdn.com/2016...8d03d9e8c8.jpg

so how do I fix it? I've tried wiggling the t-handled hex wrench in the hole, but the piece doesn't budge.. You said it needed to back out of the hole, but how do I accomplish that? I can't get hold of it with anything.

Since the screw that goes in does not actually thread into this part you can try getting a larger diameter screw to thread into the hole and use that as a grip point for pulling it out, possibly with pliers. You also may try heating the shaft to get it to expand some and loosen on the paw.

this is ridiculous! It won't budge!! How in the world did this happen anyway?

I watched a video of how to remove the spindle, and maybe I need to do that. Maybe it would be easier than working upside down. but I don't have the required flat wrench.

You can take the y-truck off without the flat wrench and that will let you bring the y and z-trucks both out of the machine to give you more room.

Looks like the barrel rolled around so the paw? is hidden and the hidden part isn't. Take the Z truck off so you can work on it. Pull the screw almost all the way out and see if you can roll the barrel 180 deg.
Clint

This is the clamping paw ...the most elusive animal on the internet .....I could not find a picture of it anywhere ...I dropped min in the machine and had to tear it half apart to find the paw .