problem carving dimension

[gcioffi]

hi help me
Done this work but did not come with size of the project.
The project is 30x30x1.8 cm 34x32x1.8 the table.
I put the other under the table so as not to ruin the machine.
The table is larger and therefore there are problems, because the design comes the goal of size?

[Jeff_Birt]

Take a look st the December and April Tips&Tricks: http://www.carvewright.com/cms/tips-and-tricks

They have a good write up on the various setting of 'Stay Under Rollers' and using various carrier boards/sleds (I think you are referring to them as table, but perhaps your are saying table to mean board?).

[Kenm810]

gcioffi,


Is it possible you didn't add 8.89 cm
to each end of you project board,
causing the pattern to be carved smaller

The Tips&Tricks: Jeff mentioned will help explain

[gcioffi]

then each project must have at least 8.9 cm to the right and left?
8.9 is the minimum distance


thanks

[TCboy]

Per reprimere il progetto da restringere quando lei sceglie di stare sotto i rulli, lei deve aggiungere almeno 8,89 cm all'asse che lei colloca nella macchina. Così, se il suo progetto è 12 cm nella lunghezza che lei dovrà collocare una 21 asse di cm nella macchina.

[TCboy]

Maybe that will help explain.

[Eagle Hollow]

Per reprimere il progetto da restringere quando lei sceglie di stare sotto i rulli, lei deve aggiungere almeno 8,89 cm all'asse che lei colloca nella macchina. Così, se il suo progetto è 12 cm nella lunghezza che lei dovrà collocare una 21 asse di cm nella macchina.

Hey Alex...That's easy for you to say!

[Audie]

I second what Atauer2 said.....I think! LOL

[gcioffi]

then each project must have at least 8.9 cm to the right and left?
8.9 is the minimum distance


thanks

[TCboy]

there are several free translators on the web that you can use. I simply typed in the information in english and translated it into italian. One site that i find useful is www.freetranslation.com. Try it out sometime.

[TCboy]

Lei dovrà aggiungere che alla lunghezza dell'asse. 8,9 cm a entrambe le fini.

[gcioffi]

then each project must have at least 8.9 cm to the right and left?
8.9 is the minimum distance


thanks

[AskBud]

then each project must have at least 8.9 cm to the right and left?
8.9 is the minimum distance
thanks
gcioffi,
If you have not downloaded the CarveWright Manual, go here and get the download file.
http://carvewright.com/cms/downloads

After you download the PDF file go to page # 29. It should be where it begins to talk about Project size v/s actual board size (Workpiece Perparation).
The drawing(s) show the Project size on the Left and the project plus the 17.79 CM (A+B) "Scrap, or uncut ends" that are needed to keep the project under the rollers on the Right drawing. If this extra length is not on your actual board, the machine will start asking if you wish to reduce the actual size of your project to "FIT" the board you have loaded into the the machine.

See if this PDF now makes sense to you.
AskBud

[mtylerfl]

then each project must have at least 8.9 cm to the right and left?
8.9 is the minimum distance


thanks

Yes, that is correct, and it is a MUST - otherwise you will invite all kinds of problems/issues. Later, after you have gained some experience with the machine, you may want to build sleds to "simulate" the extra length as far as the machine is concerned.

[TCboy]

gcioffi,

Lei ha scelto all'autojig nel software? Se così, scalerà il progetto sulla macchina.

[gcioffi]

then each project must have at least 8.9 cm to the right and left?
8.9 is the minimum distance


thanks


veramente grazie

[TCboy]

Lei è corretto. Lei dovrà aggiungere 8,9 cm alla sinistra e la destra. 8,9 è il minimo.

[SilentBob]

Concerning the translators, when I used the link posted it reads;

To suppress the project to restrict when she chooses to be under the rolls, she should add at least 8.89 cm to the board that she places in the car. So, if its project is 12 cm in the length that she should place a 21 board of cm in the car.

When I use http://babelfish.yahoo.com/translate_txt it reads;

In order to repress the plan to shrink when it chooses to be under the seams, it must add 8,89 at least cm all' axis that it places in the machine. Thus, if its plan is 12 cm in the length that it will have to place 21 axis of cm in the machine.

I just think the Babble Fish is more accurate, but since I don't know what you started with maybe not:mrgreen:

[TCboy]

bob,

Each web translator sight is going to read the information differently. I haven't tried using babelfish yet, but will give it a shot.