lawrence
10-01-2013, 05:31 PM
ALLCON,
Thank you for the interest, my Carvewright has been sold
-----------------------------------------------------------------
For sale:
Carvewright package including
Carvewright B model with card and reader
cut motor 317 hrs 12 min
scanning time 3 hrs 38 min
servoing time 343 hrs 58 min
total power on time 572 hrs 3 min
Functions fine with following exceptions - "open cover" switches have been a bit temperamental lately (sometimes requiring blow out with air or 2x shuts) - infeed sandpaper belt has had approx 1/2 inch removed - brass roller has no o-ring (has been missing for some time, does not appear to affect function) - muffler has hole taped over - cover has hole cut in it for (included) carved dust collection attachment.
Recent board sensor assembly replacement, recent replacement of bearings, recent replacement of carbon brushes (all replacements done approx at 275 hrs-300 cut motor hrs) Good flex shaft which does not get hot.
Also includes:
Rock Chuck Kit #1 (1/2 inch bit adapter - installed on machine)
1/2 to 1/4 Rock Sleeeve
1/2 to 1/8 rock sleeve
2 spindle square tools
16 new-in-package compucarve branded 1/16 carving bits (with qc adapter attached)
8 new-in-package compucarve branded 1/8 cutting bits (with qc adapter attached)
New spare parts
2x unused spindle flexshaft assemblies
2x FFC cables
1x carbon brush assembly (2 pieces)
1x board sensor assembly
1x y-drive belt tensioner assembly
also included:
extra muffler (also with taped over hole)
extra set of sandpaper belts
plastic qc bit holder case
original QC chuck and chuck tool
extra card and reader (card occasionally gives errors)
Scanning probe and 3x plastic tips (does not include pattern editor software, which is non transferrable)
Several used bits
1/2 jointing (quite dull)
1/2 ball nose (used but still usable)
90 degree v bit (quite dull)
60 degree v bit (quite dull)
60 degree CMT bit (used but still usable)
1/16 cutting bit (used but still sharp)
3/16 carving bit (used but still sharp)
1/8 cutting bit (used but still usable)
5x 1/16 carving bits - all still sharp, some possibly not used
- will also include any other extras I find laying around that will fit into the box, but this was all I could find at first glance.
- $1500 plus shipping (I have a (compucarve branded) original box and packaging for shipping) - please contact me via PM if interested.
I hope whomever buys this setup gets as much pleasure from it as I have- it is a good running machine, has served me well, and includes what I considered to be my "hobbiest lifetime supply" of cutting and carving bits. Sold "as is" but am willing to perform video function check for potential buyer before shipment or at time of local pickup.
Thank you for your consideration,
V/r
Lawrence
http://i171.photobucket.com/albums/u313/ldr_klr/P10003181024x768_zpsd5ee9411.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003181024x768_zpsd5ee9411.jpg.html)
http://i171.photobucket.com/albums/u313/ldr_klr/P10003171024x768_zpse35b9165.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003171024x768_zpse35b9165.jpg.html)
http://i171.photobucket.com/albums/u313/ldr_klr/P10003191024x768_zps2647eef0.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003191024x768_zps2647eef0.jpg.html)
http://i171.photobucket.com/albums/u313/ldr_klr/P10003201024x768_zpsae708ce3.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003201024x768_zpsae708ce3.jpg.html)
Thank you for the interest, my Carvewright has been sold
-----------------------------------------------------------------
For sale:
Carvewright package including
Carvewright B model with card and reader
cut motor 317 hrs 12 min
scanning time 3 hrs 38 min
servoing time 343 hrs 58 min
total power on time 572 hrs 3 min
Functions fine with following exceptions - "open cover" switches have been a bit temperamental lately (sometimes requiring blow out with air or 2x shuts) - infeed sandpaper belt has had approx 1/2 inch removed - brass roller has no o-ring (has been missing for some time, does not appear to affect function) - muffler has hole taped over - cover has hole cut in it for (included) carved dust collection attachment.
Recent board sensor assembly replacement, recent replacement of bearings, recent replacement of carbon brushes (all replacements done approx at 275 hrs-300 cut motor hrs) Good flex shaft which does not get hot.
Also includes:
Rock Chuck Kit #1 (1/2 inch bit adapter - installed on machine)
1/2 to 1/4 Rock Sleeeve
1/2 to 1/8 rock sleeve
2 spindle square tools
16 new-in-package compucarve branded 1/16 carving bits (with qc adapter attached)
8 new-in-package compucarve branded 1/8 cutting bits (with qc adapter attached)
New spare parts
2x unused spindle flexshaft assemblies
2x FFC cables
1x carbon brush assembly (2 pieces)
1x board sensor assembly
1x y-drive belt tensioner assembly
also included:
extra muffler (also with taped over hole)
extra set of sandpaper belts
plastic qc bit holder case
original QC chuck and chuck tool
extra card and reader (card occasionally gives errors)
Scanning probe and 3x plastic tips (does not include pattern editor software, which is non transferrable)
Several used bits
1/2 jointing (quite dull)
1/2 ball nose (used but still usable)
90 degree v bit (quite dull)
60 degree v bit (quite dull)
60 degree CMT bit (used but still usable)
1/16 cutting bit (used but still sharp)
3/16 carving bit (used but still sharp)
1/8 cutting bit (used but still usable)
5x 1/16 carving bits - all still sharp, some possibly not used
- will also include any other extras I find laying around that will fit into the box, but this was all I could find at first glance.
- $1500 plus shipping (I have a (compucarve branded) original box and packaging for shipping) - please contact me via PM if interested.
I hope whomever buys this setup gets as much pleasure from it as I have- it is a good running machine, has served me well, and includes what I considered to be my "hobbiest lifetime supply" of cutting and carving bits. Sold "as is" but am willing to perform video function check for potential buyer before shipment or at time of local pickup.
Thank you for your consideration,
V/r
Lawrence
http://i171.photobucket.com/albums/u313/ldr_klr/P10003181024x768_zpsd5ee9411.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003181024x768_zpsd5ee9411.jpg.html)
http://i171.photobucket.com/albums/u313/ldr_klr/P10003171024x768_zpse35b9165.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003171024x768_zpse35b9165.jpg.html)
http://i171.photobucket.com/albums/u313/ldr_klr/P10003191024x768_zps2647eef0.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003191024x768_zps2647eef0.jpg.html)
http://i171.photobucket.com/albums/u313/ldr_klr/P10003201024x768_zpsae708ce3.jpg (http://s171.photobucket.com/user/ldr_klr/media/P10003201024x768_zpsae708ce3.jpg.html)