mtylerfl
07-24-2012, 10:38 PM
Hello,
Here is a preview of the next Project of the Month (for AUGUST 2012), the Anchor Clock and Wooden Chain.
This project demonstrates how fun and easy it is to create a wooden chain with your CarveWright machine. An Anchor Clock was thrown in for good measure - you know - so you could connect the chain to ‘something’! The chain pattern (PTN) as well as the Anchor pattern were created using the CarveWright Designer Modeling Suite and the Pattern Editor. (The project MPC's were laid out in Designer version 1.182 in case you haven't updated to the newest version yet, and the PTN's are compatible with ALL Designer versions).
The project uses just the 1/16" Carving Bit and the 1/8" Cutting Bit. No other bits are required. The completed Chain is about 19" long (but you can make it shorter or longer) and the Anchor is about 7" wide x 10" tall x ¾" thick.
Main items you will need
1) The Project Files (included):
• Wooden_Chain_Links.mpc
• Anchor.mpc
2) Boards with the following dimensions:
Chain Links: 0.5" x 5.5" x 24”
Anchor: 0.75" x 11" x 18”
NOTE: Do not use boards that are smaller than specified above. NOTE: Make sure the chain link board is a full 1/2-inch thick. Otherwise the machine will not accept it without a sled or jig.
3) Sandpaper, wood glue (a type that dries clear such as TiteBond III), wood stain and/or paint and clear finish
4) A 2¼" Clock insert. I used a model 15686 clock from www.Klockit.com (http://www.Klockit.com)
5) A Dremel-type rotary tool with assorted sanding wheels and bits to sand small details and speed up preparation for finishing.
Apply stain/paint and clearcoat of your choice.
Here’s what I used on my Anchor Clock and Wooden Chain made from Select Pine:
Anchor
• Rust-Oleum Ultimate Stain - Black Cherry
• Bullseye Sealcoat as clear top coat (Bullseye Sealcoat is actually a clear de-waxed shellac...this is NOT the same as regular clear shellac which is NOT dewaxed)
• Krylon Clear Acrylic spray overall
Chain
• Minwax Natural Stain #209 - I dipped the chain in the can and hung it up to dry.
Here is a preview of the next Project of the Month (for AUGUST 2012), the Anchor Clock and Wooden Chain.
This project demonstrates how fun and easy it is to create a wooden chain with your CarveWright machine. An Anchor Clock was thrown in for good measure - you know - so you could connect the chain to ‘something’! The chain pattern (PTN) as well as the Anchor pattern were created using the CarveWright Designer Modeling Suite and the Pattern Editor. (The project MPC's were laid out in Designer version 1.182 in case you haven't updated to the newest version yet, and the PTN's are compatible with ALL Designer versions).
The project uses just the 1/16" Carving Bit and the 1/8" Cutting Bit. No other bits are required. The completed Chain is about 19" long (but you can make it shorter or longer) and the Anchor is about 7" wide x 10" tall x ¾" thick.
Main items you will need
1) The Project Files (included):
• Wooden_Chain_Links.mpc
• Anchor.mpc
2) Boards with the following dimensions:
Chain Links: 0.5" x 5.5" x 24”
Anchor: 0.75" x 11" x 18”
NOTE: Do not use boards that are smaller than specified above. NOTE: Make sure the chain link board is a full 1/2-inch thick. Otherwise the machine will not accept it without a sled or jig.
3) Sandpaper, wood glue (a type that dries clear such as TiteBond III), wood stain and/or paint and clear finish
4) A 2¼" Clock insert. I used a model 15686 clock from www.Klockit.com (http://www.Klockit.com)
5) A Dremel-type rotary tool with assorted sanding wheels and bits to sand small details and speed up preparation for finishing.
Apply stain/paint and clearcoat of your choice.
Here’s what I used on my Anchor Clock and Wooden Chain made from Select Pine:
Anchor
• Rust-Oleum Ultimate Stain - Black Cherry
• Bullseye Sealcoat as clear top coat (Bullseye Sealcoat is actually a clear de-waxed shellac...this is NOT the same as regular clear shellac which is NOT dewaxed)
• Krylon Clear Acrylic spray overall
Chain
• Minwax Natural Stain #209 - I dipped the chain in the can and hung it up to dry.