Ike
03-15-2012, 05:37 PM
If anyone is interested I still have my never used K2 CNC with now out dated V Carve Pro 4.5 and Photo V carve. I intended to learn and use the CNC, but the CW did everything I needed. It is a shame it just sits so I am selling it for $3000.00 now that is with the software I paid over $600.00 I think?
I have attached my original sales receipt to show what I paid without the software. If anybody is interested please PM me and I will give you my home phone number. I also am trying to sell it on e-bay.
Ike
Here is what I bought I removed the other because it had too much personal info.
CNC Router Machine KT-2514 Basic Frame Only Includes kerk Leadscrews
X-Y-Z Axis @.10 pitch. Z comes standard with 3" Z, motor mounts for NEMA23
and 3 couplers .25 I/D. (Not included:Motors,wires,home switches,E-stop,table
top,spindle, mount, software).
1 1,395.00 1,395.00T
2514-CON-SERV... (3) Axis Servo Controller Gecko Drive.
(3) 150 oz/in Close Loop Servos with encoder, Wires with Cat 5 plugs, (parallel,
USB, Power cord).
Emergency Stop switch hardware with 4 feet length wire.
Home Switches
USB plug for additional power
(Newly added relay output only. This is controlled by Mach2 - Mach3 using M
codes
*Does not include the On/Off Router spindle relay hardware – sold at an
additional charge*),
Standard 110 V can be made to 220 V with no added cost (customer must request)
1 1,550.00 1,550.00T
Mach2/3 Mach2/3 Control Software and license. (Reads G-Code - Controls CNC). Window
XP or 2000. Processor (1.00GHz) or greater. Memory 256MB DDR SDRAM.
Hard Drive 20GB. USB. Parallel port on mother board or PCI slot. All background
software to be removed from computer.
1 199.00 199.00T
1 RM-PC892 Router Mount for Porter Cable 892 Router 54.95 54.95T
R-HOOD-PC892 2007 Dust hood for Porter cable mount 892. Fits PC 892, Hitachi, Bosch, PC7518,
Makita. Fits 2.25" hose (Rigid Vacuum).
1 89.00 89.00T
R-RELAY Relay for 110V Router spindles. Used to turn on/off router via mach 2. G-Code
M03 or M04. Plugs into new control box with relay output. Good use to know
when the machine is done with program.
I have attached my original sales receipt to show what I paid without the software. If anybody is interested please PM me and I will give you my home phone number. I also am trying to sell it on e-bay.
Ike
Here is what I bought I removed the other because it had too much personal info.
CNC Router Machine KT-2514 Basic Frame Only Includes kerk Leadscrews
X-Y-Z Axis @.10 pitch. Z comes standard with 3" Z, motor mounts for NEMA23
and 3 couplers .25 I/D. (Not included:Motors,wires,home switches,E-stop,table
top,spindle, mount, software).
1 1,395.00 1,395.00T
2514-CON-SERV... (3) Axis Servo Controller Gecko Drive.
(3) 150 oz/in Close Loop Servos with encoder, Wires with Cat 5 plugs, (parallel,
USB, Power cord).
Emergency Stop switch hardware with 4 feet length wire.
Home Switches
USB plug for additional power
(Newly added relay output only. This is controlled by Mach2 - Mach3 using M
codes
*Does not include the On/Off Router spindle relay hardware – sold at an
additional charge*),
Standard 110 V can be made to 220 V with no added cost (customer must request)
1 1,550.00 1,550.00T
Mach2/3 Mach2/3 Control Software and license. (Reads G-Code - Controls CNC). Window
XP or 2000. Processor (1.00GHz) or greater. Memory 256MB DDR SDRAM.
Hard Drive 20GB. USB. Parallel port on mother board or PCI slot. All background
software to be removed from computer.
1 199.00 199.00T
1 RM-PC892 Router Mount for Porter Cable 892 Router 54.95 54.95T
R-HOOD-PC892 2007 Dust hood for Porter cable mount 892. Fits PC 892, Hitachi, Bosch, PC7518,
Makita. Fits 2.25" hose (Rigid Vacuum).
1 89.00 89.00T
R-RELAY Relay for 110V Router spindles. Used to turn on/off router via mach 2. G-Code
M03 or M04. Plugs into new control box with relay output. Good use to know
when the machine is done with program.