View Full Version : How many Carving Hours on your CW?
lynnfrwd
07-15-2010, 04:21 PM
How many Carving Hours do you have on your CW? Who has the most?
Got more than one machine? What is your total hours?
jaroot
07-15-2010, 05:25 PM
Not totally sure without actually checking but I think it is about 90.
Digitalwoodshop
07-15-2010, 05:56 PM
3 close to 1K and one about 400 from Ike that is a parts machine for the moment. Need to replace some Y bearings.
AL
liquidguitars
07-15-2010, 06:14 PM
I hope the winner get a free carbide bit or two.. never used the 1/16 bit yet. :)
Here are my times , all working 100% with the exception of my carriage adjustment on unit one I lost the right side gear pinion and it just hangs however it still carves fine as i adjust the table each load.. all units have the 1/2" Rock installed but the CT would be same i am guessing.
unit 1- 904
unit 2 -591
unit 3- 419
total cut motor time 1914 hrs
unitedcases
07-15-2010, 06:15 PM
My first machine had about 300 on it. Then my Rev B has a few more. I have replaced my controller twice but I think the first before the change was about 400, then about 270, and I just hit 65 with my new controller. I dont use it everyday but I log about 16 or so on the weekend when I can. I have got a grand in hours just all spread out. I finally learned how to ground my machine so hopefully I wont burn any more controllers.
easybuilt
07-15-2010, 08:34 PM
My first CW I purchased January 2009 has 787 on it and the used one I bought two months ago has 432 hours.
eelamb
07-17-2010, 12:05 PM
Well I got my CW in Oct 09, it has:
cut motor 31 hours 38 minutes
Power 48 hours 56 minutes
servo 38 hours 33 minutes
Scan 4 hours 19 minutes
Now who can beat these numbers (low that is)
Spencemark
07-19-2010, 05:43 PM
3 hours 49 minutes
I have 400 on my one CW and the new one expected tomorrow should have 20 minutes! Geez if I kept all the machine I have bought this latest would be number 5! My part machine I removed the cut motor so I don't know?
Ike
lynnfrwd
09-27-2011, 05:51 PM
OK, it's time to revive this thread, cause we heard today of someone with over 3500 hours on his A model machine. WOW!
myshop1044
09-27-2011, 06:09 PM
I got 1583 on my up graded B machine.
lawrence
09-27-2011, 06:30 PM
69 hours 27 mins on mine.
Holy cow it feels like I've done a lot of projects to have so few hours compared to y'alls--I feel like such a noob! Some of you have a massive amount of experience/carves.
Lawrence
Nighthawk12
09-27-2011, 08:17 PM
8) over 600 Hrs. And going strong.
rncurrie
09-27-2011, 08:28 PM
My oldest A has 1010 hr 48 min, Rock chuck, up and down draft. The next A has 35 hr 13 min, down draft and quick chuck. The B has 62 hr 8 min, up and down draft with quick chuck.
lynnfrwd
09-27-2011, 08:28 PM
8) over 600 Hrs. And going strong.
8 machines each over 600?!?
Sent from my iPhone using Tapatalk
Nighthawk12
09-27-2011, 08:33 PM
No just one machine I think you are seeing the cool face as a 8
b.sumner47
09-27-2011, 08:38 PM
I have three machines CW's. I took a look at the one That i'm using, 386 + Capt Barry
bergerud
09-27-2011, 09:29 PM
I have 533 on mine with only minor problems along the way.
easybuilt
09-27-2011, 11:06 PM
1264.34 on my first CW
664.59 on my second.
Total cut time 1928.93
Both machines working like champs.
Both with the ROCK!
CarverJerry
09-28-2011, 08:07 AM
I have 286 hours of cut time on my machine and it's a "B" I believe. I have a Rock Chuck (which I love) with the Ring Neck vacuum system on it that also does a great job keeping it clean inside. So far no major problems.......
CJ
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.