Need Help Create Pattern

[jjack9485]

I would really like someone to create pattern of this shelf, the back board only. I will gladly pay some one..the attached photo is very poor, need something similar if possible . The backboard is 20' wide and 12" high. The two bottom point should be rounded like the one to the far left.....

Jack



http://forum.carvewright.com/attachment.php?attachmentid=28042&stc=1&d=1257384670

[www.go3d.us]

Hi, the link to the picture is invalid. If you don't mind reattach the picture?
Thanks

[jjack9485]

Click on again, it opens up for me...

Thanks,

Jack

[PCW]

Jack,

It will not open for me either.

[dbfletcher]

Jack,

It will not open for me either.

Ditto for me.

[jjack9485]

see if this one works..


jack

http://forum.carvewright.com/attachment.php?attachmentid=28042&stc=1&d=1257390310

[Icutone2]

Will not open for me.
Lee

[Pratyeka]

I would really like someone to create pattern of this shelf, the back board only. I will gladly pay some one..the attached photo is very poor, need something similar if possible . The backboard is 20' wide and 12" high. The two bottom point should be rounded like the one to the far left.....

Jack



http://forum.carvewright.com/attachment.php?attachmentid=28042&stc=1&d=1257384670

Was anyone able to make a ptn for you? The picture is very hard to make out and the resulting pattern would be approximate at best. How much time do we have to come up with a decent pattern?

[jjack9485]

If we could come up with something similar would be fine, I'm sorry about the photo, tried to improve it with photoshop, thats about the best I can do. We have pleanty of time. No, nobody has been able to open up the file but you.

jack

[Pratyeka]

I can give it a shot this weekend. I was able to enhance it a bit to see some details, but if I come up with something it will be mostly inspired by what I can make out. Some of the contour is useable, so I'll use that. The rest of the details we can work on later, with your input.
I'll post the results in this thread.

[jjack9485]

Great,

The dimensions are 20"X12", not 20' , I have just taken a digital photo of the photocopy and is much clearer. I just can't figure out how to post a pic.

jack

[Woodhacker]

When ya want to post a pic, (or any gfx file) look down at the bottom of the message window you are typing in. There will be a button to "go advanced". In the advanced window, down below the "submit reply" button you will see "manage attachments". Click on that and it will open up the upload part of the thing. You may have to adjust the size of your file in order to save it. Just look at the file limit sizes for whatever type of file you want to post.
Click on the "browse" button to navigate to where your file is. Double-click on the file. Then click on the "upload" button/

Hope this helps

[Pratyeka]

If we could come up with something similar would be fine, I'm sorry about the photo, tried to improve it with photoshop, thats about the best I can do. We have pleanty of time. No, nobody has been able to open up the file but you.

jack

Here's what I could come up with, about 1 hour playing with it. That's the basic outline extracted from your jpg and mirrored to make it symetrical. It makes a good foundation to add details on top, if you want.
Tell me if you want something added of changed before I post it.

[glenfoxman]

Ive never used the smart scissors before, and I just tried them and I couldnt figure it out.

Id recommend to just erase the backgrounds from pictures or use paths, if you need help with that I can give some tips :3
_______________________________________
Website I designed for cash advance loans (http://www.paydaytown.com) company.

[jjack9485]

Ok , I think this link will work...

...jack

http://www.flickr.com/photos/10134857@N06/4095265958/

or maybe this one....

http://www.flickr.com/photos/10134857@N06/4095265958/

[ajk]

attached the photo
hilda