View Full Version : Bar stools
bizbiki
02-27-2009, 08:42 PM
Hi all,
Been a long time. I am going to make 5 barstools and want to use the CC to carve the seats. This way they will be uniform and the same. My question is this I want to make rear end depressions (that would be butt prints for those in Louisiana) on the seats, does anyone have the standard demensions for this and a way to do it on the cw.
This is not a joke. I am serious.
thanks
FINGERS
02-27-2009, 09:04 PM
Do a search for a dish you can use that just invert the pattern or if you can sit on a scanner, naaaa!
mtylerfl
02-27-2009, 09:06 PM
Hello,
I tried searching for barstool ergonomics, barstool butt, barstool plans and came up empty - could not find any "guideline" for the seat contour.
Maybe put chalk on your "sweet spot", sit down on a black sheet of paper, and use that as a template. ;)
That's all I can think of to do other than just make a calculated "guess".
FINGERS
02-27-2009, 09:21 PM
do a search for go-3d-dish I think this will work for what you like to do.
FINGERS
02-27-2009, 09:36 PM
Here you go try this with some sanding I think you can make it work
Dan-Woodman
02-27-2009, 10:10 PM
Hey Biz
Try this one . I have no idea where it came from ,so use it at your own risk. Good to hear from you again. It's also adjustable.
later Daniel
roughcut
02-27-2009, 11:00 PM
Ain't that something you step in when you are out thar in the woods?
geekviking
02-27-2009, 11:13 PM
If you're not careful... :cool:
bjbethke
02-27-2009, 11:50 PM
Hi all,
Been a long time. I am going to make 5 barstools and want to use the CC to carve the seats. This way they will be uniform and the same. My question is this I want to make rear end depressions (that would be butt prints for those in Louisiana) on the seats, does anyone have the standard demensions for this and a way to do it on the cw.
This is not a joke. I am serious.
thanks
I've made several stools with the CW machine, Works great, I sand the center some and round over the bottom. Hope this helps.
JOHNB
02-28-2009, 06:35 AM
this(these) might help. someone(lhr?) got the butthead award a while back. couldn't find it, so here it is again. stretch it according to your size? heh-heh
Kenm810
02-28-2009, 09:08 AM
Hey that looks like a good combination ! :razz:
pine acres woodshop
02-28-2009, 10:14 AM
The butt prints are nice, are these stools going to have a back on them? if they are I would go with the butt prints, if they don't have a back on them, can I make the suggestion that you might want to just make a dish on the top otherwise you would have to sit on the stool a certain way or it might be uncomforable.
Mark
SeaCapt97
02-28-2009, 01:15 PM
Wow! Talk about your heart shaped ###! Ken - I need to know who modeled for you . . .
Kenm810
02-28-2009, 02:10 PM
Ah ---- Promised I wouldn't tell !! ---- :razz:
bizbiki
03-01-2009, 08:32 PM
Wow! two pages of responses in one day.
Thanks for all the help.
I will use mikes idea and see how it works out.
Thanks Mike
Grampy122
03-04-2009, 03:47 PM
Maybe you would like a Scottish bar stool.
yellowdog
03-04-2009, 03:56 PM
Now that's just funny, I don't care who you are!
fyrpuppy
03-04-2009, 09:53 PM
Yes that is for KILT wearers. Hope they have handiwipes available.
bayea
03-05-2009, 05:18 PM
I want a pattern for the Scottish bar stool !!!! that is too funny.
bjbethke
03-05-2009, 05:52 PM
I want a pattern for the Scottish bar stool !!!! that is too funny.
The CW won't carve that deep :)
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.