- Project unreadable code 6 and code 9
- Z axis stall error 246
- Z axis and Y axis causes
- Customer RA Form (Fillable).pdf format
- problem with start position
- Close Cover Error - Over & Over - y not disable it
- how do i cut out design with carve writght
- Looking for pattern
- QC? Broken out of the box
- do you use the head locking leaver or not
- Sensor
- Check your boards
- screw loose
- Do you get the "Cannot Read Flash Card" message?
- Compression roller head stuck in the up position.
- Sophie has the Wobbles......
- CW Registration site down?
- Flash Card Will Not Be Recognized
- another clean sensor error
- help
- Probe Failure - Check Probe
- Y Axis Error
- Edge Detection Prob? Not Sensor?
- No display after "Memmory card error"
- Fatal Exception 181
- Father's Day went bad
- Z-axis stall error 246
- What is best Lubricant?
- Phantom Lines?
- what's this
- z-axis stall error 236
- Replacement of the X Stage 2 Gear in Pictures
- Check cut motor error
- Check Board and Sandpaper Belt Quality
- Hopefully Just a Little Problem
- electrical glue for ribbon cables
- bit not turning
- Hot Z Truck
- Stuck wide open
- cut motor wires
- Now that doesn't sound right
- A note about replacing ones traction belt...
- Tech Support 800 number
- Bit finder
- ?! Help.. Cutting to deep
- Another Board Sensor Question
- Board Sensor update
- Rear compression roller problem..
- Display panel
- Getting replacement machine
- Where to start?
- Hot Shaft
- what the heck
- Stuck Chuck
- Support Link?
- Cut out (mis)alignment problem +
- Found bolt...help please:)
- Board Measuring Problem
- Speed or Me ??
- Display problem
- I think I killed my machine
- Lowering Head on the board
- z-motor pack
- Crank won't crank
- Clear Board Sensor
- going home
- wont powr up after x-axis error
- Solved my Z Stall after the 3rd time.....
- cut too deep
- Close cover and clean y rails
- Breaking Bits
- calibrating Head pressure
- oddly quiet but seems to still be carving alright
- Static electricity
- Messed up sensor
- Centerline Font Problem
- New Machine
- Need Help with Striking Plate
- Check Cut Motor
- finding bit position
- Z stall help!
- Z creep down, cutting too deep.
- sand paper ripped
- Cutting to specific dimensions
- Cut Motor Brushes failed at 298 Hours
- fatal error 181
- Anyone in Az want to buy my machine?
- close cover to...
- err code 400
- unable to lift top after carve
- X overload error
- x axis error 500
- Sled want stay in Machine
- X overload
- Smooth Operation
- Yet another edge sensor question.....
- CCM fix?
- Found Part
- HELP gear assembly
- Ok - Solved My X Overload Error
- Anatomy of a Cut Motor 101
- Help please
- Anatomy of the Z Truck
- carving bit
- Log On Backwards?
- Route Edge Problems
- Check Cut Motor
- A kink in the traction belt?
- repaired machine
- Error 226, Check Motor
- Star & text problem
- Flex Shaft Vibrating
- change sandpaper
- Just in case this happens to you
- y motor pack
- Clear Board Sensor... here we go again
- Unsupported bit
- nothing on the screen, please help!
- Problems during carve
- under pressure
- Machine Does Not Measure Lenght
- "search" won't work for me?
- Measures Board Length VERY Slow
- Another flex shaft problem
- Crank clutch won't clutch!
- Post error codes & fixes
- Anatomy of the Z Encoder 101
- Need Help Installing New Cutter Motor Asap! Too Many Wires????
- Squeak from Z-Truck bearings
- motor spins during measure
- Stationary cutting head
- How do I remove the Board Sensor?
- The State of RELIABILITY......
- error with Z Axis 246
- How to send carvewright back to company
- install the crank handle
- Flipper won't flip
- Two machines down at once.... :(
- Spindle bearings
- Forum search minimum word length
- Y axis stall error 236
- Measures but won't touch board!
- stuck bit
- Fatal Error- reboot system
- Stair Stepping
- Another "Check Cut Motor Issue"
- What am I doing wrong.....?!!!!
- Check Motor Unit
- Mystery Part
- Anatomy of a NEW Z Bundle
- How Do I get at the back roller mechanics?
- Is there a exploded diagram?
- Routing to a depth
- Z Truck Help
- Z-axis homing sensor
- Vertical Lockup
- Could be a new FAILURE to Watch....
- Fatal Error CODE 3
- board sensor housing
- Error messages ?
- LHR Phone Issues?
- Close cover error
- Clear boartd sensor
- LHR Involvment
- Torn belt
- Motor doesn't start
- 236 Y Axis error saga
- finding bit plate
- exceptional stack error 181
- Step by Step help please
- eror 12288 everytime i upload, or try
- multiple [rpjects on one board
- Broken bit
- Found this bolt
- Support Link
- Oblong Holes Drilling
- Static Cling
- Happy New Gear!
- New user woes.
- ZAXIS Stall
- Stuck in Scan Mode
- Keeps returning to Homing load carving bit
- Font Chatter
- Sensor Problems
- Bit holder doesn't turn
- Lemon machine??
- Chatter/tearout
- No Project on Card, or Card Error
- Z axis stall problems.
- my machine is stuck in scan
- UP! Chuck!
- Stuck roller
- Set Screws Question
- Board Sensor
- Z axis stall
- Bits wont stay seated.
- Jerky Y-travel
- Customer Service
- Preventive Maintenance
- Machine shuts down
- Machine can't measure depth
- Error 204 - Found a Solution
- Carving bits
- lines in carving
- Router Air Cut
- bit flapper
- Problem measuring thinner board
- Advice needed: replacing gear in drive train for sandpaper belts
- Stuck in Accessory Menu
- some questions/problems with the unit
- Missing Letters? Any Suggestions?
- stops carving mid way through - carves the air
- Can't make the curve!
- LCD is Blank
- Our Favorite Trouble Shooter is on the loose
- I want honest answer !
- K mods, I believe you
- cut motor keeps running
- wgrigsby:Flapper Fix
- Sliding Plate!
- Can a project be started if machine is shut down?
- when I turn it on it goes straight to accessory option
- Would like help learning
- Can't Find end of board
- head crank clutch
- z axes stalled
- close cover
- Quick release
- Axis stall error 236
- Will they call back
- Carving depth
- QC Chuck
- Newbie encounters problem 1st carve
- Carving problem - possibly traction related
- Screws falling out
- A word of Thanks
- catastrophic z truck failure
- Cannot do anything
- new user needs help
- Error Received when submitting Error Data!
- Can't run my software...
- Unknown Part
- Spot the deliberate mistake
- Looks like time for a new "Z" pack ...
- Machine keeps running the board out
- Portraits
- Uneven Carving
- carving problem please help
- Why doesn't 3/8" material work?
- close cover error