View Full Version : CarveWright Machine
Pages :
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
[
18]
- Help! Anyone near Pearland that can carve 7 signs for me this week? I will provide
- Somerset, NJ woodworkers show .
- DON'T USE-Liquid Wrench Chain Lube
- Frustrations with error messages and shut downs
- Hey everyone I am back
- Caution to everyone to pay attention!
- Cover Switch
- Board Tracking Assembly
- Board runs threw during measurement issue
- clear acrylic carving
- Carvewright/elec. circuit question.
- are you getting error messagess saying your card is corrupt?
- why, suddenly, does "load bit"keep recycling?
- One more DC hose grounding question.
- Z Axis Stall ERR E06-0324
- Portable Carvewright - Generator + UPC
- Attempting to use CW as cross-section 3D printer, but plagued by X-axis issues
- Sandpaper belts
- Multiple errors
- Looking for a document/tutorial
- Computer readouts
- Melted plastic on flex shaft
- Jogging to position using 60-degree V bit
- Y/Z Motor Gear
- Just curious
- Brass Pinions on Servos
- rotary jig belt
- A vs C macine functionality
- It just went blank-won't turn on
- Snapped Z Truck bolt?
- removed traction belts now found rubber piece
- Board thicknes
- Melting flex shafts
- CW in storage just before new carvetight chuck. What 1st, lube, etc. before turn on?
- CW in storage long time. How can the noise be reduced?
- A day that will never be forgotten !!!
- Cut motor brushes
- Time for a WAG
- Designer dimensions vs cut dimensions
- Repeat Last Operation
- no heavy duty traction belts????
- Mystery broken piece - A machine
- Outfeed Trays
- Marble Wood
- z truck plunged (totally plunged!)
- Bit height above collet
- z-truck stall
- Trying to find a CW user near me
- After Market Memory Card Programmer
- Just finished replacing my "A" machine sandpaper belts with rubber ones... BOOM BABY
- What caused this?
- Board size tolerance:
- Spare memory cards?
- musslechuck
- Static shock no power
- Can this Flex Shaft be saved...
- Sandpaper drive belt ripped into starting a project. Guess it's time to upgrade
- Jogging - Can't wrap my mind around this one....
- Shavings in Z motor
- What damage does removing memory card with power ON cause?
- Rear access through cover
- Truck Movement
- Y motor replacement on an A machine
- cut motor brushes
- Removing the old ptobe cable
- z axis timing belt change
- Sent machine back
- Help! I cannot seat the Flexshaft into the top hat of the Z truck!
- planing / rabeting bit
- Lose Z Truck
- Flex shaft heats up
- Slipping crank
- CW Maintenance
- Cut Motor Abuse or Takes a Lickin and Keeps On Tickin
- Y stall with a vector graphic
- Z-axis help
- Close Cover even after new installed
- check cut motor... :(
- replacing O ring
- Head way off level
- Tracking problem....Maybe ??
- Has LHR mitagated the Y bearing problem?
- Ordering parts from Canada
- cut motor grinds
- Repair or Replace (a testament to dust collection)
- Rockler Sales and Canada
- X Drive problem
- Board ejected from machine?
- Not sure what to call this issue
- Better outfeed roller adjustment
- Machine won't come on
- Replacement parts
- Back up and running
- Carvewright and Rockler
- ffc cable
- Crank part
- Battery Backup
- Dust Collector Evaluation
- Carving Bit
- Lights for the CW
- need brush cap
- Machine carving to deep
- Replacing the Y belt
- X Drive Gears gone bad?
- flexshaft installation
- New clock USAF
- X-Termination Electronics Board
- front cover replacement
- Cut Motor Case Replacement
- Machine Bolt pattern ?
- Head cover cable harness removal---too much adhesive
- Cleaning up machined sides
- Green wood, esp. black locust and burls
- Need advice... starting carving up again.
- Close door
- Board Measurement inconsistent
- Love and Hate!!! 2 week of struggle :)
- Big problem here
- New Flex Shaft
- Cable replacement tips and tricks?
- Need to raise the tool
- Errors, Errors, oh my!
- New problem
- AC Switch bypass
- Cut motor rebuild
- Just a little tip about board thickness
- traction belts
- Carve Tite questions
- Odd behavior y axis stall
- Possible dead controller
- First my Flexshaft, now the Cut Motor... stumped, help appreciated!
- Carving Cypress ?
- Board measuring problem workaround
- Machine Location in the House?
- y-motor pack
- Issue with Z Truck
- Y offset calibration
- Stuck flex shaft
- Are calibration numbers "forgotten"?
- Lubricating Flex Shaft
- Mufflers on the CX
- Z axis stall
- Replacing clear cover
- Officially licensing university logos
- Carving moved over 3 inches during carve
- updates in the last 5 years ???
- Understanding your Cut Motor, Let NORM help.
- Here is one I haven't seen before
- Replace Board Sensor Wire
- Broken Hinge on Outfied Tray
- New parts
- A question about maintenance costs
- Maintenance after 3 Year Layoff
- DFX Import Problem
- Machine goes back to main menu
- Accessory Menu
- Uneven floor - why?
- ER 20 Spindle
- Jog to position
- Z stall error solved and potential problem discovered
- Frustrated
- More than a little off-center
- rebuild by factory?
- Z Axis issues for vector text
- Where is everyone?
- Lubrication of the crank and head posts
- X-Drive Gear
- Measurements
- New style Y gearbox
- Red Head lock
- proceed board message
- Using a power converter with the Carvewright for 220 to 120v
- Y axas ERROR
- Bit plate not coming out but trying to
- Head movement
- background lines
- Parts included with HD Traction Belts?
- Unable to access Menu choice 0 - Options
- loading board
- Carve Malfunction
- Sticking card.
- Carvewright User Guide/Manual
- Carving confusion.
- Machine just stopped
- Loading a board
- Board movement during carving
- Circles with a blip
- Help with a project
- Operation temperature
- Board encoder vs X motor encoder. Which is the master and which is the slave?
- Internal lighting for CW machine
- Repair of dead card reader
- Staying under the rollers
- machine
- Computer not reading disk
- Broken Flexshaft didn’t ruin my day!
- Had an error when I flipped my board
- Is the board sensor affected by cold?
- Centerline depth issues
- Recover a project after breaking a bit???
- How long do cut motor brushes last?
- Clutch torque plate
- Table Mount
- Board Sensor
- Anybody ever figure out the feeds and speeds?
- Ensure Sliding Plate Set - deeper board
- 18 pin cable
- Traction belt
- x drive gear replace
- tracking issue
- Y axis drive belt
- The New Raven
- z qaxis stall question
- Y drive belt
- Customer Support
- Colorado Services
- power fluctuation
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.