Thank you all for the input. I will check for someone in the area.
Thank you all for the input. I will check for someone in the area.
I could not agree more with DickB. I had major problems from the dust until I purchased a dust hood attachment . (Available in third party accessories) I already had a 2hp dust collector. I use the 4 inch opening and it collects 98 % percent of the dust. Very little clean up. I bought the one with the 4 inch hole on top. Black in color. Works great.
Here's my opinion for starting out - I just bought mine in the past few months. I'm sure others will not agree but to quote The Dude, hey man, it's just, like, my opinion man.
Machine:
I suggest just getting the basic machine package for starting out. It's probably going to take you a handful of carves to get used to the software and machine. You can make amazing things with just the standard 1/8 cutter and 1/16 carving bits.
Dust collection - I see that as a luxury and not a necessity (but definitely in my future) but you definitely need *something* to use to clean the machine out. I have an inexpensive "pancake" air compressor with an "air blower" chuck for it that I use to clean out the machine. I open the machine lid every 20 minutes or so during a carve and blow the sawdust out. It sure makes a mess but it's cheaper than a big dust collection system (see notes below on DIY dust collection)
Hearing protection - this machine is loud and will certainly damage your hearing. Hearing damage is cumulative and permanent. After a life of guns, guitars and motorcycles lemme tell you - tinnitus SUCKS. I use shooting earmuffs. You can pick up a pair for about $10 just about anywhere (Walmart, Dicks, etc). You can also use the cheap little foamies. Doesn't matter what you use but you're going to want hearing protection.
As far as bits go it is highly recommended to use CW bits.
As someone else posted, go ahead and order flexshaft lube. Per the maintenance schedule you don't need it until 100 hours of use but it's very inexpensive and you may as well order it with everything else.
You posted about mounting it on a miter saw stand and something about rollers - I'm a little confused by that. The CW has infeed and outfeed trays with rollers. And they fold up . I wouldn't suggest hanging the machine if for no other reason it's taller than it is wide. i think it would effectively take up more space.
Having said all that...
Since you want to make signs the centerline text will be in your future. I bought it as well as the v-bits and so far I haven't used the v-bits a single time. I certainly will at some point.
I bought the keyhole bit and software add-on. I understand it's not difficult to buy a keyhole bit and program the cuts yourself but it's a no-brainer with the software.
Lastly, if/when you go to get a true dust collection system there are several commercial "cyclone" products (like Oneida's Dust Deputy) but some savvy people have built them from scratch. One guy built the "cycone" part of his using metal rolled into a cone. Someone with vision beyond mine went to Home Depot and bought a road cone for that part(that is blanking brilliant). Personally, I'm on the fence because building one will cost at least $25 and a bunch of my time. The Dust Deputy is $50 and looks more professional. /shrug
http://www.instructables.com/id/Dust...-Traffic-Cone/
I forgot to add something - you'll want a sanding mop. You can buy them anywhere (like the CW store) but you can make one yourself for very little money using drywall pads (they look like window screen covered with abrasive), a bolt, a nut, and a couple of washers. I more or less followed the below video but instead of using a band saw to cut the pads I used a pair of scissors. And the vid uses cloth sandpaper but I used drywall pads. I think it took me all of an hour to make it. Run it in a drill press or a handheld drill.
I do not recommend cleaning the machine only by blowing with an air compressor. The enemy in my opinion is very fine dust particles that get into bearings, optical encoders, and other parts. Blowing can move these fine particles into these places. Get or make a top-mount dust collector. It is not an option in my opinion.
I could not agree more with DickB. Blowing sends all of the sawdust into the electronics and moving parts of the machine.
The only thing WORSE than blowing is sucking with a shop vac.
As far as I'm concerned, a top mount system should not be an option and should not be added later. I try to sell one with EVERY machine I sell.
CarveWright CX Packaged System - starting at $2000
CarversClub 1 Year Subscription - $150.00/year
Adv. Support w/out CC membership - $25.00/issue
CarveWright Community Forum - PRICELESS!
I agree with Dick.
Blowing dust around in the machine WILL cause you problems.
Although I don't use my machine as often as I once did, my down-draft
cabinet and ground-wire protected vacuum hose has served me well.
I like the idea of a good above-the-belts DC system, but don't like my big
DC unit running all the time my machine is on.
Connie was faster than I was.
I see that she does not like my use of a shop-vac!
Ken,
V-1, 2, & 3
When the People fear their Government, there is Tyranny.
When the Government fears the People, there is Liberty.
- Thomas Jefferson
You must be the change you wish to see in the world.
- Mohandas Gandhi
The follow is copied and pasted from the Carvewright maintanence page:
http://www.carvewright.com/support-page/maintenance/
The CarveWright is designed to tolerate a considerable amount of carving system dust, but to ensure proper operation it should be kept free of debris as much as possible. Periodically blow or vacuum out any dust or debris from the recesses of the unit. Always make sure to use low-pressure air (<80 psi) around the electronics and sensors. High-pressure air can damage components and actually push dust into them.
So now you, as a Carvewright employee, are telling me to ignore what's on your own ding dang maintenance page. So now I'm ordering the dust collector. When I read somewhere else that I shouldn't have one I'm sending it back.
Can you understand why a customer might get frustrated at such a situation?
I do understand. Everybody has their own favorite way of doing things. Some swear by center on board, others jog to position. Some prefer one method of lubricating flex shaft, while others have their own.
At shows, I vacuum a machine, but I also know the part in the manual that warns against electrostatic discharge. Here, we blow them out, but when running a project, we use a dc insert. We also know how to clear dust from board sensors.
For newbies, it's just A LOT safer to say DON'T DO IT!!
CarveWright CX Packaged System - starting at $2000
CarversClub 1 Year Subscription - $150.00/year
Adv. Support w/out CC membership - $25.00/issue
CarveWright Community Forum - PRICELESS!
The machine does tolerate a fair amount of dust IF it is cleaned out well after each carve. Vacuuming it out by making sure the machine is turned off, vacuum hose kept away from machine electronics (key board especially), grounding yourself to the machine while vacuuming and using low pressure air to blow out the crevices and crannies in the machine.
Having a top mount dust collection system attached to the machine allows the user to do multiple carves back to back without doing the deep cleaning described above.
If you do not see a noticeable difference and not 100% satisfied I will buy it back....
RingNeckBlues
My patterns on the Depot
DC-INSERT It Just Sucks!
Proven to out perform all others!
Buy CarveWright
Colorado FaceBook Users Group
All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.