Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: new one on me; Y belt slip error

  1. #1
    Join Date
    Jan 2008
    Location
    New Iberia, la.
    Posts
    1,866

    Default new one on me; Y belt slip error

    I tried this 3 times just to make sure, when the truck hits the swing plate, it snaps it, the second time it does not.
    it gave me this error, I oiled the swing plate and tried it again, same error, when I hit enter to continue , it gave a "y" stall error.
    my "Y" belt is tight, there is no warble in the "Y" truck, the gear box is not loose. What do I looker for now.
    see attached.
    any help would be great
    Perry B.
    Attached Thumbnails Attached Thumbnails y slip error 2.jpg   y slip error 1.jpg   swing plate error.jpg  
    My Shop 1044

    CarveWright START U Team Member

    V - 1.187 and 3.0 too
    With the DC Insert," dust all gone"
    CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
    CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
    www.customcarvingsbyperry.com
    I have often wondered why it is that
    Conservatives are called the "right" and Liberals are called the "left".
    "The heart of the wise inclines to the right, but the heart of
    the fool to the left."

  2. #2
    Join Date
    Nov 2008
    Location
    Vancouver Island
    Posts
    8,193

    Default

    It seems very likely that then y belt is slipping at the first thwack at the bit plate. Mark the y motor sprocket and the belt with a felt pen and try it again. If it is slipping, re-tighten the belt and try it again. (I would give the tightening spring a little "help" for the purpose of trouble shooting.)

  3. #3
    Join Date
    Apr 2013
    Location
    Cornwall, Ontario, Canada
    Posts
    1,343

    Default

    It happened to me a few times and it was because the wires for the cover were in the way. May want to check that too!
    Suzanne

  4. #4
    Join Date
    Jan 2008
    Location
    New Iberia, la.
    Posts
    1,866

    Default

    I did take a look at the wires also and pushed them back down, Are you talking about the tension sprocket ?
    My Shop 1044

    CarveWright START U Team Member

    V - 1.187 and 3.0 too
    With the DC Insert," dust all gone"
    CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
    CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
    www.customcarvingsbyperry.com
    I have often wondered why it is that
    Conservatives are called the "right" and Liberals are called the "left".
    "The heart of the wise inclines to the right, but the heart of
    the fool to the left."

  5. #5
    Join Date
    Nov 2008
    Location
    Vancouver Island
    Posts
    8,193

    Default

    Quote Originally Posted by myshop1044 View Post
    I did take a look at the wires also and pushed them back down, Are you talking about the tension sprocket ?

    Yes, the sprocket on the right with the set screw and the spring tensioner. If you think the belt really is slipping (and I think it is), undo the set screw to let the spring re tighten the belt and then re tighten the set screw. (If the set screw happened to be loose, that would actually be the problem.)

  6. #6
    Join Date
    Jan 2008
    Location
    New Iberia, la.
    Posts
    1,866

    Default

    Thank you I will try it tomorrow, have to see the fireworks with one of the grand kids.
    My Shop 1044

    CarveWright START U Team Member

    V - 1.187 and 3.0 too
    With the DC Insert," dust all gone"
    CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
    CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
    www.customcarvingsbyperry.com
    I have often wondered why it is that
    Conservatives are called the "right" and Liberals are called the "left".
    "The heart of the wise inclines to the right, but the heart of
    the fool to the left."

  7. Default

    I had one where the "cords" all broke. The Y timing belt was basically just a giant rubber band. Replaced the belt and all was well.

  8. #8
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    I would remove the Y gearbox and inspect the Big Plastic Gear for worn out 685ZZ Bearings and the Y Encoder for dust.

    AL
    Attached Thumbnails Attached Thumbnails DSC01478_WEB.jpg   DSC01476_WEB.jpg   DSC00488_WEB.jpg   DSC00486_WEB.jpg  

    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  9. #9
    Join Date
    Jan 2008
    Location
    New Iberia, la.
    Posts
    1,866

    Default

    I'm up and running again, after doing the marking of the sprocket ,still the same error, I removed the gear motor and what did I see ,"teeth missing".
    change the "Y" belt, lucky I had one, and no errors.
    thanks for all the help and suggestions. Now I go and order 2 Y belts, 2 machines.
    Perry B.
    Attached Thumbnails Attached Thumbnails Y belt teeth missing 001 (600 x 450).jpg  
    My Shop 1044

    CarveWright START U Team Member

    V - 1.187 and 3.0 too
    With the DC Insert," dust all gone"
    CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
    CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
    www.customcarvingsbyperry.com
    I have often wondered why it is that
    Conservatives are called the "right" and Liberals are called the "left".
    "The heart of the wise inclines to the right, but the heart of
    the fool to the left."

  10. #10
    Join Date
    Nov 2008
    Location
    Vancouver Island
    Posts
    8,193

    Default

    Good work. Another one to add to the list! I do not think I have seen that type of failure before.

    (If you did not have the extra belt, I bet you could have flipped it over.)

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •