I think this is what you are after. Just scroll down the you see Nurses Plaque
http://forum.carvewright.com/misc.ph...chments&t=2046
I think this is what you are after. Just scroll down the you see Nurses Plaque
http://forum.carvewright.com/misc.ph...chments&t=2046
Last edited by PCW; 05-02-2009 at 06:16 AM.
I'm looking for a Cat 980 front end loader if anyone out there knows where I can get one.
Wow! Have seen some beautiful patterns here thanks for all of them.
Here is a chain saw carve did a few years back and scanned it hope you enjoy half as much as I have enjoyed the patterns you have given.
Good day
Ray
OK Guys & Gals, I just finished the Vector conversion of the Lion & Lamb.
I set it up to use the 60 Degree bit set at a depth of 0.065".
This design takes 57 minutes to carve v/s 2 hours & 17 minutes for the original using the Carving Bit.
Eighteen minutes of both carves are used by the "Edge" cutter.
If you have not watched the video on Designing a Stain Glass Project, you will find it here:
http://www2.wcoil.com/~nharbison/cw-...0downloads.htm
AskBud
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Nice job Bud,
And if you do the edge routing with a hand router
or on a router table it will be even faster.
Ken
Ver 1.182 on XL Pro plus Ver 1.164 and 1.175 on Windows 7 Ultimate
It Never Fails * Till * You Say It Never Fails
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Hey Bud
I've never been able to open your tuterals.
I just tried this one "open" and a little bar came up saying something about you need this to open "click here" so I did that,nothing. I then started over and "saved" , that worked but I don't know what program I need to be in to open it for videos.
later Daniel
1.187 Custom Woodworking for more than 40-years
Daniel,
They are ZIPed AVI files. Therefore, you may have to unZIP them and them open them with Windows Media Player or some other Media player. Just check the specs (permissable File Type(s)) on the Media Players you have on the PC.
In XP, once you find the correct player you may set you default for AVI by these steps:
1) Go to My COMPUTER > TOOLS > FOLDER OPTIONS > FILE TYPE/
2) When the list appears, drop down to AVI and set it to that Player.
3) Click APPLY > OK.
AskBud
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Thanks, just what I was looking for.