Christmas is Coming....

[STEAM]

Hope you don't mind Jason that I am adding this pattern to your thread. It's an old pattern I got back in the 80's. It would make a great gift for someone.

[badger]

Like you can't get to it at all - or just the link that you ahve saved isn't working......

Cant get to it at all. Every time I try the link it just loads but never gets there and finally times out. The saved one, the one you had listed here even just typing it in. I can get to it from work just not my home system anymore.

[HighTechOkie]

I was having problems earlier also. I just checked and it loaded fast and okay now.

Rob

[RayTrek]

Hello to all
Wanted to get a early start this year so that maybe I can get them in the local gift store they have been asking for them, What is cool is that I have gotten to carve some patterns that I have wanted to see.
Will get back to you with more picks, as they get finished,
They are all about 4 and a quarter tall (best) in select pine/craft 36" x 5.5" x ½” about 5 dollars at Lowes, I use a piece of white electrical phase tape for the board sensor with the .5 wood projects like this.
Ray
Tip of the day, a new sharp bit will make a big differance in qulity of carve and machine effort.

[RayTrek]

Good Day Everyone,

I have been busy with some other projects and want to get back to finishing this one. The MPC files are what I have carved each one was carved on select pine 36” x 5.5” x.5” at best and approximately 3 hours for each one cut out and all, used a dermal for clean up and ready for painting.
There are 27 patterns that I have collected from my patterns, and from here, and other sites. I removed the Santa with the staff light torch and put in another Santa head I had, the torch is to brittle for this type of carving.
Hope to get back to you soon with some of them finished.
Enjoy ~ Ray using Ver. 1.153
Thank Jason for the “CNC Art Guild” that has allowed me to post the MPC files in there original size and post the links here.
And thanks to all that PM me with your comments they are greatly appreciated.

http://www.mediafire.com/file/1uukdyjyk55/christmas2009 4r.mpc

http://www.mediafire.com/file/hay3mnfgwxm/christmas2009 1r.mpc

http://www.mediafire.com/file/tltuytyiwtd/christmas2009 3r.mpc

[robbrigg2]

Good Day Everyone,

I have been busy with some other projects and want to get back to finishing this one. The MPC files are what I have carved each one was carved on select pine 36” x 5.5” x.5” at best and approximately 3 hours for each one cut out and all, used a dermal for clean up and ready for painting.
There are 27 patterns that I have collected from my patterns, and from here, and other sites. I removed the Santa with the staff light torch and put in another Santa head I had, the torch is to brittle for this type of carving.
Hope to get back to you soon with some of them finished.
Enjoy ~ Ray using Ver. 1.153
Thank Jason for the “CNC Art Guild” that has allowed me to post the MPC files in there original size and post the links here.
And thanks to all that PM me with your comments they are greatly appreciated.

http://www.mediafire.com/file/1uukdyjyk55/christmas2009 4r.mpc

http://www.mediafire.com/file/hay3mnfgwxm/christmas2009 1r.mpc

http://www.mediafire.com/file/tltuytyiwtd/christmas2009 3r.mpc

Ray these are great. Tank you very much. They make great projects for me kids and me!

[LittleRedWoodshop]

for the MPCs Ray - lots of work to do now...........

[Digitalwoodshop]

Ray,

Thank YOU for your Work setting them up, looks like I will need to get 1.153.....


AL

[Icutone2]

Thanks Ray, I will also try to cut some out!
Thanks Lee

[Kenm810]

Nice Job! Ray,

The GrandKids will Have ball painting and coloring them!!
Plus a little more Quality time for Grandpa.