hummm --- than ya defiantly don't need this one
Running Ver1.34 on this Pc and didn't see your sample files.
hummm --- than ya defiantly don't need this one
Running Ver1.34 on this Pc and didn't see your sample files.
Ken
Ver 1.182 on XL Pro plus Ver 1.164 and 1.175 on Windows 7 Ultimate
It Never Fails * Till * You Say It Never Fails
Ike planters are great. I found in AR you need to haul your garden in. In the hills where I live it is all rocks, it's called CHAT. Most of the summers here it does not rain for over a month at a time. This is a planter you may need to add water only once ever other week.
It is a take apart unit, long side 17 inches - short side 13 inches. The plastic tub was from Wal-Mart $2.00 each. All joints are loose dove tailed. 12 inches high - Cedar boards.
Using Designer Version 1.187
Donations are always welcomed, thanks – send a check to my PO Box 652
BJB
PO Box 652
Yellville,AR 72687-0652
PM me for my e-mail address.
BJ, my Dad makes redwood wishing wells and wine barrel fountains and small planters. He is making a wheel barrel and I thought what a great project idea. I am at a fair with my shop so my CW is there. But I have the plans just about done.
I have used planters for veggies and other plants myself! Thank you again for your help and everybody else too. Like I said, I had a brain fart! My mind has been preoccupied with my new Grandson!
Ike
Michael T
Happy Carving!
╔═══ Links to Patterns & Resources for CompuCarve™ & CarveWright™ ═══╗
Lol I believe it Michael! I bet my won't be as good as yours, but I will give a whirl! I really wanted to help my Dad with his wheels, he cuts them by hand and ...well they are almost round! Plus he just started making them and they look great, but he has not got the angles down yet.
Don't cross your plan off just yet, but thank you for putting it on the back burner. Oh thank you for correcting my other brain fart, wheel barrow not wheel barrel!
Ike
Bud asked,
I understand the method of assigning rectangles/circles to make my tabs in the various versions. The question is,"How do I get the TAB Option to activate on version 1.15" What situation/setting does it apply to? So far, I have not see anything that it works on. What am I missing?Tab Option
AskBud
--------------------------------------------------------------------------------------------------
Bud,
New Tab Option:
Draw a line across any opening. Highlight it then pick on the new Tab Option. You will get a new on screen box with tab options (width and height). That's it. You can pick multiple lines also.
Last edited by hotpop; 07-30-2009 at 01:16 PM.
Mel
Patterns for sale at CW's Pattern Depot
Check out "Yankee Pop's Shop" at
http://www.carvewright.com/store/pat...nkeepop&page=1
--------------------------------------------------------------------------------------------------
Bud,
New Tab Option:
Draw a line across any opening. Highlight it then pick on the new Tab Option. You will get a new box on screen box with tab options (width and height). That's it. You can pick multiple lines also.
Last edited by hotpop; 07-30-2009 at 01:20 PM. Reason: Typo
Mel
Patterns for sale at CW's Pattern Depot
Check out "Yankee Pop's Shop" at
http://www.carvewright.com/store/pat...nkeepop&page=1
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29