Search:

Type: Posts; User: johnsonswamp; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    4,321

    Looks great, I like how you changed the back rest...

    Looks great, I like how you changed the back rest looks good. I stop by from time to time but haven't touched the CW in a long time other than moving it out of my way. Was going to upload it to the...
  2. Replies
    14
    Views
    2,957

    A vast majority of the stuff I cut out when I...

    A vast majority of the stuff I cut out when I used the machine was 48"+, my machine is VERY picky with boards that long so I learned to run them through the table saw to square it up and put tape on...
  3. Replies
    13
    Views
    3,763

    Here's my "fix", but like I said for me it was...

    Here's my "fix", but like I said for me it was free and works perfect.



    68327
  4. Replies
    13
    Views
    3,763

    I'll take a picture tomorrow for you. But I took...

    I'll take a picture tomorrow for you. But I took a piece of I think it was 1/4 angle iron I had laying around, drilled 2 holes through it and the open side of the bottom where dust falls through and...
  5. Replies
    13
    Views
    3,763

    I had this same problem, couldn't get pressure...

    I had this same problem, couldn't get pressure right and it was hard to lower/raise. Turn machine over and remove bottom cover, check the screws holding the rod up to the screw posts, mine was broken...
  6. Replies
    14
    Views
    3,695

    Here is the blade I have, I love it. Smooth clean...

    Here is the blade I have, I love it. Smooth clean cuts, and good on the budget.

    http://www.amazon.com/gp/product/B00008WQ2Z/ref=oh_details_o01_s00_i04?ie=UTF8&psc=1
  7. Replies
    0
    Views
    1,220

    Scanning Probe

    Brand new in box, took probe out to see if machine would detect it, has no adapter as it was for a rock chuck, can send a quick connect with it if needed, software has NOT been registered. Unforeseen...
  8. Someone could try this. ...

    Someone could try this.

    http://ohiocarbon.com/docs/Helpful-Order-Form-1.pdf

    http://ohiocarbon.com/products/industrial
  9. Replies
    12
    Views
    7,246

    Thanks, plugged it into the z truck this morning...

    Thanks, plugged it into the z truck this morning and changed the setting to truck and it works now.
  10. Replies
    12
    Views
    7,246

    I have not done the upgrade and its the older...

    I have not done the upgrade and its the older cable. I have a plug on the side cover that I plugged the adapter into, but the z truck also has a nut plug looking thing on it. Tomorrow I'll see what...
  11. Replies
    12
    Views
    7,246

    Probe stuck closed

    My probe came in, I haven't registered it yet because I wanted to make sure everything with it on my machine (wires) would work before I got stuck with it, does the software have to be registered...
  12. Replies
    6
    Views
    2,306

    Thanks for the info everyone, now that I know...

    Thanks for the info everyone, now that I know it'll carve good I'll go ahead with it. Just gotta figure out WHAT to put on it, I can build furniture and stuff off imagination, but when it comes to...
  13. Replies
    6
    Views
    2,306

    That is something I was wondering about, I've...

    That is something I was wondering about, I've never used the jog to option. So I mark the dead center of my oval piece, then jog the bit to that spot and it centers the pattern off it?
  14. Replies
    6
    Views
    2,306

    End grain carving

    I have a slice of a walnut tree I'm thinking about carving on, should it turn out like a normal carve or does it carve differently? Was thinking either a carve, centerline text, or both. Not sure...
  15. Replies
    3
    Views
    2,436

    That is it stretched out. No I didn't, it is...

    That is it stretched out.


    No I didn't, it is one out of the pattern depot I believe, I wish I could make them like that.

    Here is cypress...
  16. Replies
    3
    Views
    2,436

    wood selection

    I have a customer wanting a carving done in the pic below, he wants it 14"x30", I kinda unsure of stretching the pattern out. My main question is he is putting it on a cypress wall so I don't know...
  17. Replies
    18
    Views
    6,437

    It's the 2hp harbor freight DC

    It's the 2hp harbor freight DC
  18. Replies
    18
    Views
    6,437

    Here is where I'm at so far. Red is DC piping,...

    Here is where I'm at so far.

    Red is DC piping, all 4" and reduced at tool, all 45* turns, metal blast gates and floor hose for table saw, rest is run along ceiling and hoses dropped down. will...
  19. Replies
    18
    Views
    6,437

    I need some help, been trying to gather up...

    I need some help, been trying to gather up everything i need online and getting a major headache from all the confusing info online. Was thinking thin wall pvc, but trying to figure out all the...
  20. Replies
    18
    Views
    6,437

    Good deal, was hoping it would. Now I gotta...

    Good deal, was hoping it would. Now I gotta figure out how I want to route the DC in the shop, only 4 tools but along a 20' bench and one turn for 6'. Thinking 4" pipe under the bench and plumbing...
  21. Replies
    18
    Views
    6,437

    Dust collection

    I'm looking at the ringneck blues dc insert, I already have a hard enough time changing bits with my limited hand movements so would need to set it out to change bits. Would it work without bolting...
  22. Wonder what grade bolt it is.

    Wonder what grade bolt it is.
  23. Replies
    5
    Views
    2,732

    The ball nose bit, have had it for years and...

    The ball nose bit, have had it for years and never used. Do you think it will do OK?
  24. Replies
    5
    Views
    2,732

    1/4 ball tip for cut through

    Can the 1/4 ball tip be used for a slot through 3/4" stock? If so, 1/8 or 1/4" max pass? Have a quick project my uncle asked for, and it needs a straight, 11"x1/4" slot through the board as a rod...
  25. Replies
    52
    Views
    12,093

    IP Ban them

    IP Ban them
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4