Search:

Type: Posts; User: Bubbabear; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: My Cut Motor

    by Bubbabear
    Replies
    3
    Views
    1,456

    My Cut Motor

    I guess things can overheat. SO how much is new cut motor
  2. Replies
    4
    Views
    1,611

    Recommended Liquid Wrench Chain with Moly most...

    Recommended Liquid Wrench Chain with Moly most ace hardware stores can get it
  3. Replies
    5
    Views
    1,819

    There is how it was when I opened the cover....

    There is how it was when I opened the cover. First time top has been off since last time it was in shop for them to repair z bundle and some other things
  4. Replies
    5
    Views
    1,819

    also would this break cause the z axis errors 298...

    also would this break cause the z axis errors 298 and 308
  5. Replies
    5
    Views
    1,819

    Any suggestions

    any suggestions on how to stop this from happening this is number 4 of these cables. one that came on the machine one LHR replaced and two I have replaced the one shown is last one replaced at...
  6. Replies
    29
    Views
    8,222

    Well finally got feeling well enough to go to the...

    Well finally got feeling well enough to go to the shop and do a carve. I think this box is going to look fantastic once I complete it. Did mine out of rough Cedar.

    Think I will send it to my...
  7. Replies
    7
    Views
    2,190

    Ran it appears to have gone away on mine since I...

    Ran it appears to have gone away on mine since I changed to 1.132
  8. Replies
    59
    Views
    12,394

    If the 0,5,6,1 then set depth (I set mine a .125)...

    If the 0,5,6,1 then set depth (I set mine a .125) didn't fix the broken bit. The I guess I would stop using it. But i certain cases and times I sure do like it. I would also call LHR
  9. Replies
    4
    Views
    1,650

    Where are you located whats the temps inside your...

    Where are you located whats the temps inside your shop. Needs to be at least 55f so the greases are warm enough to let it go up and down the guides properly
  10. Replies
    6
    Views
    1,883

    Check the contrast button below the 0 on the...

    Check the contrast button below the 0 on the kepad turn it both ways see if you get lcd
  11. Replies
    6
    Views
    2,206

    If they did not upgrade the entrance line when...

    If they did not upgrade the entrance line when you upgrade the box then it could be the line or the transformer on the pole. Could also be corrosion on connectors in the disconnect outside or in the...
  12. Replies
    3,314
    Views
    3,110,637

    Sticky: SO Ken can we said I made you smile If so then my...

    SO Ken can we said I made you smile If so then my years in that setup was well worth it
  13. Replies
    6
    Views
    2,206

    Dan mine does not do that but I keep getting...

    Dan mine does not do that but I keep getting power flucuation errors and stop after 2 new power supplies.
  14. Replies
    15
    Views
    4,096

    3-in-1

    http://www.3inone.com/products/telescoping-spout/

    I love the spout and 3-in-1 is a good light weight oil
  15. Replies
    7
    Views
    2,245

    Ken I know some still do not believe it but since...

    Ken I know some still do not believe it but since I added lights to the inside of my machine I don't seem to have that issue anymore. here is the link to the thread....
  16. Replies
    59
    Views
    12,394

    easier find

    So it is closer to here and no searching
  17. Replies
    15
    Views
    4,096

    Jon since I don't see where you are located I...

    Jon since I don't see where you are located I will also state temps. 55F or higher. When my shop gets about 50 the bit plate almost makes it out far enough. Days like today my tools are lonely. It...
  18. Replies
    59
    Views
    12,394

    No Chris before you start the setup go 0,5,6,1 on...

    No Chris before you start the setup go 0,5,6,1 on the keypad then it stays set until you change it gives you 4 options as I listed in #17 using the up down arrow key
  19. Replies
    59
    Views
    12,394

    Chris in 1.132 you can change the cut board to...

    Chris in 1.132 you can change the cut board to size when you are at the machine. Post 17 in this thread has it in detail
  20. Replies
    2
    Views
    1,869

    Ike I think it is a great idea. I hope there is a...

    Ike I think it is a great idea. I hope there is a huge turnout so big it makes your head spin. You in my opinion are one of the top rated designers in the forum if not the top rated you do such great...
  21. Replies
    15
    Views
    3,880

    Very good site Deolman I sure wish we could get...

    Very good site Deolman I sure wish we could get Leo LaPort and the whole gang from tech tv back again
  22. Replies
    59
    Views
    12,394

    Sorry Michael that is what ever one thought I was...

    Sorry Michael that is what ever one thought I was talking about when I had the problem I was having. But it was the one that is fixed with 1.132 so I thought I would mention it
  23. Replies
    59
    Views
    12,394

    If I am following this right this is when you...

    If I am following this right this is when you have gone to the CW put the card in and setting what pattern you want it ask if you would like for it to cut out the pattern.

    When you turn the...
  24. Replies
    15
    Views
    3,880

    I am mostly with go3d. Ram is dirt cheap right...

    I am mostly with go3d. Ram is dirt cheap right now. You will probably need an antivirus because you will most likely get it on the net to get updates for designer and maybe even Dl some of the...
  25. Replies
    16
    Views
    3,604

    LG it will go 3/4 3/8 or 1/4

    LG it will go 3/4 3/8 or 1/4
Results 1 to 25 of 441
Page 1 of 18 1 2 3 4