Search:

Type: Posts; User: trplbogie; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    77
    Views
    70,030

    Sticky: I wish I could have made the conference, and...

    I wish I could have made the conference, and thanks lynnfrwd for the invite for Friday night. I was a real pleasure to be around so much talent and to meet the Legends Of Carvewright. And of course...
  2. Replies
    0
    Views
    1,347

    Hole in One Plaque

    Anyone have Hole in One design to share or sell???
  3. Replies
    12
    Views
    4,265

    Thanks

    Thanks Bud, I am using the rock, but some simple 3 in 1 oil took care of it for now
  4. Replies
    12
    Views
    4,265

    z-axis error 313

    I keep getting Z-Axis 313 error message and cannot figure out. Comes up after putting in 1/16 carving bit and starts the homing process

    Thanks in advance
  5. Replies
    0
    Views
    908

    CarveWright Bits

    Very pleased that the new bits with pressed on shank and the small rubber spacers all work very well with the rock chuck also....along with Floyd Harris's dc.....carving is even better. When ny rock...
  6. Thread: Mahogany

    by trplbogie
    Replies
    10
    Views
    2,946

    Thanks, the one piece cut, I did not stain but...

    Thanks, the one piece cut, I did not stain but put an acrylic spray on it. I am trying to go to brush on poly, to save on costs. Out of ignorance, what is BLO?

    Thanks again
  7. Thread: Mahogany

    by trplbogie
    Replies
    10
    Views
    2,946

    The plaques will be 17x11 1/4, there will be over...

    The plaques will be 17x11 1/4, there will be over 20 total. They will be for inside display, team awards for all female redfish rodeo tournament. I want to have the nicest finish possible as I have...
  8. Thread: Mahogany

    by trplbogie
    Replies
    10
    Views
    2,946

    just the goss and no stain????

    just the goss and no stain????
  9. Thread: Mahogany

    by trplbogie
    Replies
    10
    Views
    2,946

    Mahogany

    What is the best finish for Mahagony, I have considered Minwax natural and also teak oil.
    Any suggestions??
  10. Replies
    7
    Views
    2,324

    What is the problem with the roller? and where is...

    What is the problem with the roller? and where is the machine, and hours
  11. Thread: Staining

    by trplbogie
    Replies
    8
    Views
    2,231

    thanks...look for more ideas

    thanks...look for more ideas
  12. Thread: Staining

    by trplbogie
    Replies
    8
    Views
    2,231

    stain

    I do use the pre stain conditioner especially on pine. trying to double up on the ends on single coat the rest.

    Thanks
  13. Thread: Staining

    by trplbogie
    Replies
    8
    Views
    2,231

    Staining

    Probably on the forum somewhere, just can't find it. How do you keep the cut ends of the boards from staining darker then the other edges.

    Thanks
  14. Thread: New Chuck

    by trplbogie
    Replies
    5
    Views
    2,675

    New Chuck

    Any news on the new chuck??? After complete maintainance on mine, it is having just a few small problems, but find myself having to get new bits. Funny how all my bits fit well except the 1/8 and...
  15. Thread: Sanding help

    by trplbogie
    Replies
    7
    Views
    2,160

    I should have asked my wife.....she just handed...

    I should have asked my wife.....she just handed me Glad Press'n Seal plastic wrap. Lightly tacky on one side and not expensive at all. Will try that, and after I screw up my machine I will take it to...
  16. Thread: Sanding help

    by trplbogie
    Replies
    7
    Views
    2,160

    Makes me wonder if blue painters tape would work.

    Makes me wonder if blue painters tape would work.
  17. Thread: Sanding help

    by trplbogie
    Replies
    7
    Views
    2,160

    Sanding help

    I could use tips about sanding. I typically paint a lot of lettering. I cut, then put heavy coat of gloss....spray paint then sand...pain in the .....

    Any suggestions to make this easier. Also...
  18. Replies
    9
    Views
    3,344

    shellac

    So. you stain also before shellac and carving? Then the paint just wiippes off. Or did you not stain the wood as I cannot tell from the photo
  19. Replies
    13
    Views
    3,296

    error

    Thanks again
  20. Replies
    13
    Views
    3,296

    message

    It has Univ of Bama Logo, but it is Alumni logo and I have alumni permission to use If this is the one with the cutouts it is the correct one
  21. Replies
    13
    Views
    3,296

    error

    yeah it says it's sorry. Contact LHR for support or fix. At least it apologized:)
  22. Replies
    13
    Views
    3,296

    Error message when compiling project

    Has anyone ever gotten the error 24 when project was compiling to the card?
    I tried 2 uploads of basically the same pattern but one would load the other gets the error message. And of course it is...
  23. Thread: rock chuck

    by trplbogie
    Replies
    20
    Views
    6,620

    QC

    Got a new QC and two new bits. They gave me a pretty good idea of what their new device will be and it sounds very good. As with anything time will tell. I get to go to LHR some and they are always...
  24. Thread: rock chuck

    by trplbogie
    Replies
    20
    Views
    6,620

    QC

    Sitting here at LHR waiting for my QC to be replaced. Still cannot believe it is not warranty. However everyone here is very nice. New one is supposed t be out in Jan. Sounds like it will be the way...
  25. Thread: rock chuck

    by trplbogie
    Replies
    20
    Views
    6,620

    Dissatisfied with QC

    I may have to convert to rock chuck. I have had my machine 3 weeks, and nothing but problems with the QC. I believe I am very good with my cleaning. I clean it out with each bit change even during a...
Results 1 to 25 of 33
Page 1 of 2 1 2