Search:

Type: Posts; User: Roy Fleshman; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    7,171

    Thank you Any idea which format is the best one...

    Thank you
    Any idea which format is the best one to,purchase?
  2. Replies
    3
    Views
    7,171

    Seeking Army Seal

    I have seen some photos posted and some seals. But the one I am looking for has the cannon balls. I thought there was a place to purchase it, but I cant find it. Any help appreciate it.

    86947
  3. Replies
    9
    Views
    2,444

    Great input Doc. I went ahead re lubbed and bent...

    Great input Doc. I went ahead re lubbed and bent the wire. So far no problems after another two hours of carving/ Also no heat in the rubber. It must of rubbed and I didn't notice it for a bit....
  4. Replies
    9
    Views
    2,444

    I guess that is a possibility. I thought it was...

    I guess that is a possibility. I thought it was part of the canble assembly. I remember there was a twist tie, I removed. I thought that is what I need to remove. I will check it out tomorrow. Thanks
  5. Replies
    9
    Views
    2,444

    Any suggestions

    I noticed this a few minutes ago. Took the closest photo i could take and still stay in focus. The black wire looks like it could have rubbed it, but it doesn't look like it. The copper sheathing is...
  6. Thanks everyone, I learned a few techniques and...

    Thanks everyone, I learned a few techniques and terms, picked up some tips and locations for bits.
  7. Thanks UC! Very simple with the feather. I had...

    Thanks UC! Very simple with the feather. I had added depth but the feather did the trick. I am not sure where to add draft or even what it means. Can you elaborate.

    Thanks
  8. Forgot to add this description. It would...

    Forgot to add this description. It would essentially be a cone shaped hole, roughly the profile of the first .5 inch of a typically pen.
  9. Pen holder for desk plate. Tilted cone Pen Holder

    I have searched all over the forum and could find nothing that seemed close.

    What I am trying to do is make a tapered hole around 3/4 inch deep. It would start maybe from .5 inch tapering down to...
  10. Called Tech Support. They had to clear my account...

    Called Tech Support. They had to clear my account of computers and I re-registered. Simple process.
  11. Thanks a lot for the input. I finally gave up....

    Thanks a lot for the input. I finally gave up. Not a happy camper with the amount of money I have spent. I really don't understand why this is so limiting and difficult. Time is limited and I really...
  12. I found the location to sign in. But I already...

    I found the location to sign in. But I already have two licenses registered to the same computer, which is this one and no matter what I try it won't activate.
  13. Yes My computer did an automatic update. It has...

    Yes
    My computer did an automatic update. It has done this before without a problem. Maybe this is the issue. I tried to log on in the store and I don't see anything on machine ID. Is there somewhere...
  14. Unable to use software, Wants me to register all over again. Any ideas?

    I booted up the PC this morning, the same one I have all my software installed on. I went to launch Designer 3 software and it asked me to register, etc using all the prompts. I tried every...
  15. First of all thanks for coming up with such an...

    First of all thanks for coming up with such an innovative design and project. I have made four so far and personalized each with with their name and or different carving patterns on the top and...
  16. Replies
    8
    Views
    3,371

    Isabella Cradle

    It's been a few weeks since my last post. I seem to either have no time or nothing to share. The attached photos are of a cradle I completed today using the Carvewright. I would like to mention that...
  17. Not sure what happened to cause this alignment problem

    Hi Guys,
    Seems like the best practice with problems is to upload photos and the file. So if I did this incorrectly, I apologize in advance. I still have newbie-itezs. I am building a cradle for the...
  18. Replies
    9
    Views
    10,225

    Sweet job, K! Love what you did. I downloaded it...

    Sweet job, K! Love what you did. I downloaded it all. The grandson has hi, but his sister will be arriving in about a month. I have two years I figure before I give this a try. I have a feeling this...
  19. Replies
    10
    Views
    6,273

    Butternut would have been my guess a few years...

    Butternut would have been my guess a few years back. But having spent considerable time trying to learn some wood identification because of the access to many different kinds here and hand carving,...
  20. Replies
    9
    Views
    10,225

    K, I don't even you. I made a set of those about...

    K, I don't even you. I made a set of those about three months ago for the grandson. It was spurred on by receiving a large number of 2.5X2.5 x 18 inch oak shorts in perfect condition, surfaced all...
  21. Today's Carvings and Lessons from the front line

    Attached are three photos of carves I did today. The large yellow one with the CT logo is something I am playing with for work. Never hurts to curry favor right? Anyway, it was done on a scrap of...
  22. Replies
    6
    Views
    3,031

    Yes those are exactly what I am looking for. PM...

    Yes those are exactly what I am looking for. PM message on the way.
  23. Replies
    6
    Views
    3,112

    BJ, That is a very nice pattern. I can already...

    BJ, That is a very nice pattern. I can already envision it on a nice piece of walnut. Appreciate you sharing it and the others.
  24. Replies
    6
    Views
    3,031

    Thanks Dale, I appreciate it.

    Thanks Dale, I appreciate it.
  25. Replies
    6
    Views
    3,031

    Thanks Dale, exactly what I needed. So now the...

    Thanks Dale,
    exactly what I needed. So now the question is, with everything else it cost to get to this point, is a subscription worth it? Anyone? And what is the best value? Are their patterns...
Results 1 to 25 of 40
Page 1 of 2 1 2