CarveWright Users' Forum

Welcome To The CarveWright Users' Forum

This is an online community enabling members to share knowledge on using the CarveWright and Craftsman CompuCarve machines and software.

  

Go Back   CarveWright Users' Forum > Users > Troubleshooting
Reload this Page no detail in pattern
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
Page 2 of 2 < 1 2
 
Thread Tools Display Modes
  #11  
Old 2 Weeks Ago
Kenm810's Avatar
Kenm810 Kenm810 is offline
Senior Member
  
Join Date: Jan 2007
Location: South East, Michigan
Posts: 4,099
Thumbs up
Great Project!!

I'm sure it should make an outstanding Carving.
Attached Thumbnails
Click image for larger version Name: Stain Glass Panel 1a.jpg Views: 53 Size: 64.7 KB ID: 27959  
Attached Files
File Type: mpc Stained Glass Panel 1a.mpc (858.9 KB, 35 views)
__________________
Ken

Ver. 1.134 -- Ver. 1.152 -- Ver. 1.153
Hint -- If you can, Save Time plus Ware & Tear on Cut-Motor and Machine
By doing your Finish Front and Back Edge Routing with a Hand Held Router or on a Router Table. --- I alwasy do
http://www.carvewright.com/cms/customer_service
It Never Fails * Till * You Say It Never Fails
Last edited by Kenm810 : 2 Weeks Ago at 03:57 PM.
Reply With Quote
  #12  
Old 2 Weeks Ago
Ike's Avatar
Ike Ike is offline
Senior Member
  
Join Date: Apr 2008
Posts: 1,601
Default
Well I didn't mean the project wasn't cool! I meant I wasn't sure how it will carve from a close up look of the pattern.

Shacky needs the pattern downsized and it looks great at the larger size.

Ike
__________________
Lilly and Dad last Halloween! I'm so busy...
I don't know if I found a rope or lost my horse
Reply With Quote
  #13  
Old 2 Weeks Ago
Kenm810's Avatar
Kenm810 Kenm810 is offline
Senior Member
  
Join Date: Jan 2007
Location: South East, Michigan
Posts: 4,099
Default
Not what I meant, I actually up-sized it a little more, I was just saying that I liked the Graphic Subject.
__________________
Ken

Ver. 1.134 -- Ver. 1.152 -- Ver. 1.153
Hint -- If you can, Save Time plus Ware & Tear on Cut-Motor and Machine
By doing your Finish Front and Back Edge Routing with a Hand Held Router or on a Router Table. --- I alwasy do
http://www.carvewright.com/cms/customer_service
It Never Fails * Till * You Say It Never Fails
Reply With Quote
  #14  
Old 2 Weeks Ago
Ike's Avatar
Ike Ike is offline
Senior Member
  
Join Date: Apr 2008
Posts: 1,601
Default
Lol just razzing you Ken!!

Ike
__________________
Lilly and Dad last Halloween! I'm so busy...
I don't know if I found a rope or lost my horse
Reply With Quote
  #15  
Old 2 Weeks Ago
PCW's Avatar
PCW PCW is offline
Member
  
Join Date: Feb 2009
Posts: 977
Thumbs up Learned another valuable lesson
Quote:
Originally Posted by Kenm810 View Post
Great Project!!

I'm sure it should make an outstanding Carving.
What a difference in detail by raising the rectangle by .250 made. Good Job
__________________
Dan

CarveSpot
Need a support document for the CW/CC?
Home of the Rock Chuck CW-PARTS.com
Top mount CW/CC Dust Collector Ringneck Blues
Reply With Quote
  #16  
Old 2 Weeks Ago
Ike's Avatar
Ike Ike is offline
Senior Member
  
Join Date: Apr 2008
Posts: 1,601
Default
Gee I took the rectangle out maybe should have left it in? Shacky is wanting the project to be smaller quite a bit smaller around 3.25 by 9" for the whole project.

Ike
__________________
Lilly and Dad last Halloween! I'm so busy...
I don't know if I found a rope or lost my horse
Reply With Quote
  #17  
Old 2 Weeks Ago
Shacky Shacky is offline
Junior Member
  
Join Date: Sep 2009
Posts: 96
Default
I'm getting the feelin' that there is just too much there to get a good carve in that small of a space.

I do appreciate you fellows working on it.
Reply With Quote
  #18  
Old 2 Weeks Ago
Kenm810's Avatar
Kenm810 Kenm810 is offline
Senior Member
  
Join Date: Jan 2007
Location: South East, Michigan
Posts: 4,099
Default Just a Try at it
I got to 3.005" X 9" with out very much distortion in Designer,
roll the mpc around and you,ll see what I mean.
Attached Thumbnails
Click image for larger version Name: 3 X 9 SGP.jpg Views: 28 Size: 47.1 KB ID: 27976  
Attached Files
File Type: mpc Stained Glass Panel 2a.mpc (858.7 KB, 24 views)
__________________
Ken

Ver. 1.134 -- Ver. 1.152 -- Ver. 1.153
Hint -- If you can, Save Time plus Ware & Tear on Cut-Motor and Machine
By doing your Finish Front and Back Edge Routing with a Hand Held Router or on a Router Table. --- I alwasy do
http://www.carvewright.com/cms/customer_service
It Never Fails * Till * You Say It Never Fails
Reply With Quote
  #19  
Old 2 Weeks Ago
Ike's Avatar
Ike Ike is offline
Senior Member
  
Join Date: Apr 2008
Posts: 1,601
Default
Quote:
Originally Posted by Kenm810 View Post
I got to 3.005" X 9" with out very much distortion in Designer,
roll the mpc around and you,ll see what I mean.
I guess the only way to see how it will turn out is to do a test carve!

Ike
__________________
Lilly and Dad last Halloween! I'm so busy...
I don't know if I found a rope or lost my horse
Reply With Quote
Reply
Page 2 of 2 < 1 2

« Previous Thread | Next Thread »

Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 12:14 AM.

Contact Us - www.carvewright.com - Archive - Top

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.