CarveWright Users' Forum

Welcome To The CarveWright Users' Forum

This is an online community enabling members to share knowledge on using the CarveWright and Craftsman CompuCarve machines and software.

  

Go Back   CarveWright Users' Forum > Educators > Carvewright Machine
Reload this Page flex shaft
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
Page 1 of 2 1 2 >
 
Thread Tools Display Modes
  #1  
Old 2 Weeks Ago
bogwojny's Avatar
bogwojny bogwojny is offline
Junior Member
  
Join Date: Feb 2009
Posts: 21
Default flex shaft
Anyone knows how much a new flex shaft is form carver wright?
Reply With Quote
  #2  
Old 2 Weeks Ago
Spanglerg@hotmail.com's Avatar
Spanglerg@hotmail.com Spanglerg@hotmail.com is offline
Junior Member
  
Join Date: May 2007
Location: Mechanicsville, Md.
Posts: 78
Default
Quote:
Originally Posted by bogwojny View Post
Anyone knows how much a new flex shaft is form carver wright?
bog, What happen to your flex-shaft?
__________________
GREG

I CAN FIX ANYTHING BUT A BROKEN HEART OR AN EMPTY POCKET BOOK....WHERE'S THE DUCT TAPE?
Reply With Quote
  #3  
Old 2 Weeks Ago
MCGEE2SKINNER's Avatar
MCGEE2SKINNER MCGEE2SKINNER is offline
Junior Member
  
Join Date: Jun 2007
Location: Lancaster Pa.
Posts: 141
Default shaft
I don't know how much the shaft is but the outer case is $75.00
JIM
Reply With Quote
  #4  
Old 2 Weeks Ago
bogwojny's Avatar
bogwojny bogwojny is offline
Junior Member
  
Join Date: Feb 2009
Posts: 21
Default
was about to start a carve and it wanst turning the bit so i took the flex shaft out and it was coming unwired at end.
Reply With Quote
  #5  
Old 2 Weeks Ago
Spanglerg@hotmail.com's Avatar
Spanglerg@hotmail.com Spanglerg@hotmail.com is offline
Junior Member
  
Join Date: May 2007
Location: Mechanicsville, Md.
Posts: 78
Default
Quote:
Originally Posted by bogwojny View Post
was about to start a carve and it wanst turning the bit so i took the flex shaft out and it was coming unwired at end.
bog, Can't say I have heard of this issue. I'm sure someone will have some advice. Make sure you determine the cause of this situation, because I'm certain it goes a lot futher than the flex-cable. Good Luck!
__________________
GREG

I CAN FIX ANYTHING BUT A BROKEN HEART OR AN EMPTY POCKET BOOK....WHERE'S THE DUCT TAPE?
Reply With Quote
  #6  
Old 2 Weeks Ago
bogwojny's Avatar
bogwojny bogwojny is offline
Junior Member
  
Join Date: Feb 2009
Posts: 21
Default
I never did lube the flex shaft when I got the machine but its worked fine for months until the qc broke then I replaced it with the Rock. Went to carve and the shaft wasnt turning the bit. I had used the machine the day before and it worked fine but today took a crap. Im gonna call the company abot the flex shaft as well as the thin spring that surrounds it and get a replacement for both. Not sure if it comes separate or all as one piece.
Reply With Quote
  #7  
Old 2 Weeks Ago
jab73180's Avatar
jab73180 jab73180 is offline
Junior Member
  
Join Date: May 2009
Location: Deep in the woods of Maine
Posts: 148
Default
the shaft is $75, i just bought one cuz i melted the outer sheath. that comes with the sheath, spring and core.
__________________
-Jason


ver 1.153 with the ROCK!!

Nothing goes as planned, whats the fun in that
Reply With Quote
  #8  
Old 2 Weeks Ago
bogwojny's Avatar
bogwojny bogwojny is offline
Junior Member
  
Join Date: Feb 2009
Posts: 21
Default
What i just realized was when I went to cut out some patterns the first day I accidently used the carving bit instead the cutting bit....that could have caused the problem with the flex shaft right?
Reply With Quote
  #9  
Old 2 Weeks Ago
mtylerfl's Avatar
mtylerfl mtylerfl is offline
Senior Member
  
Join Date: Dec 2006
Location: Brunswick, GA
Posts: 3,324
Default
Quote:
Originally Posted by bogwojny View Post
What i just realized was when I went to cut out some patterns the first day I accidently used the carving bit instead the cutting bit....that could have caused the problem with the flex shaft right?
That would certainly have added a great deal more stress to the machine and flex shaft alright.

However, when you get the new flex shaft, be sure to lube it with the Chain Lube with Moly as per CarveWright's recommendation. I've only had to lube my two machine's flex shaft's once and that was over two years ago. No sign (yet) of needing to be re-lubed. One treatment lasts a long time, apparently!
__________________
Michael T
Happy Carving!

╔═══ Links to Patterns & Resources for CompuCarve™ & CarveWright™ ═══╗

Visit the CarveBuddy Website for Additional Exclusive Patterns and Resources
Reply With Quote
  #10  
Old 2 Weeks Ago
bogwojny's Avatar
bogwojny bogwojny is offline
Junior Member
  
Join Date: Feb 2009
Posts: 21
Default
gotcha about the grease/lube
Reply With Quote
Reply
Page 1 of 2 1 2 >

« Previous Thread | Next Thread »

Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 07:46 PM.

Contact Us - www.carvewright.com - Archive - Top

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.